AEG 72330 manual Run a Washing Cycle, Brief Instructions, Set the Washing Program

Page 18

Instructions for use

Run a Washing Cycle

Brief Instructions

A washing cycle is run in the following steps:

01. Set the correct washing program:

–Set the program and temperature with the program selector

–Set any additional program(s)

2.If necessary, change the spin speed/select RINSE HOLD (GEEN CENTR., SANS ESSOR.).

3.Open the filling door and fill with washing.

4.Close the filling door.

5.Add washing detergent/care agent.

6.Start the washing program.

After the Washing Program Ends:

Attention! If the washing cycle ended with Rinse Hold, before opening the filling door carry out PUMP (POMPEN, VIDANGE),

SPIN (CENTRIFUG., ESSORAGE) or SHORT SPIN (KORT CENTRIFUG., ESSOR. DELICAT).

7.Open the filling door and remove the washing.

8.Switch off the washing machine: Set the program selector to OFF (UIT, ARRET).

Set the Washing Program

3For a suitable program, the right temperature and possible additional programs for the relevant washing type, refer to the ”Program Tables”.

0 1. Set the program selector to the required washing program with the required temperature.

18

Image 18

Contents ÖKO-LAVAMAT 72330 update Dear customer Tel /3630444Contents Remedying Faults What to do ifContents Safety Before Putting into Operation for the First TimeCorrect Use Child Safety General SafetyDispose the packing material DisposalEnvironment Tips Dispose the old applianceUnit Description Front ViewDrawer for Washing Powder and Care Agent Control Panel Program SelectorEASY-CARES KREUKHERSTELLEND, Defroissable Woollens WOL, LAINE/P HandwashAdditional Program Buttons PRE Wash VOORWAS, PrelavConsumption Values and Time Requirements What Does Update Mean? Before the First WashPrepare the Washing Cycle Sort and Prepare the WashingWashing Types and Care Codes How much washing detergent and care agent? Water SoftenerWater Hardness Details Set the Washing Program Run a Washing CycleBrief Instructions After the Washing Program EndsChange Spin Speed / Select Rinse Hold If necessary, change the spin speed for the finalOpening and Closing the Filling Door Add the WashingCompartment for in-wash stain treatment If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Compartment for pre-wash agent/soaking agentChanging a Washing Program Start the Washing ProgramCompletion of the Washing Program Program Sequence DisplaySelect the Additional Program Change the Spin SpeedWashing Cycle Ended/Remove Washing Program Tables WashingEASY-CARES PRE Wash Separate Conditioning/Starching/Impregnating Separate RinseSeparate Spin Cleaning and Care Washing Detergent DrawerWashing Drum Filling DoorRemedying Faults What to do ifAdjust in accordance with Sans Repassage Rinsing water is Cause is probably a If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Clean the Solution Pump When all the washing solution has drained offEmergency Unlocking of the Filling Door Cancel Additional Rinse Additional Rinse RINSE+/SPOELEN+/RINCAGE+Set Additional Rinse Child Safety Feature Setting the Child Safety FeatureCancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for InstallationSetting Up the Unit Remove the Transport SafeguardTransporting the Unit Close off the hole with the plug cap G Prepare the Installation Location Setting Up on a Concrete PedestalSetting Up on a Vibrating floor Compensate for Floor Unevenness Electrical Connection Water ConnectionPermissible Water Pressure Water Inflow Water Drainage Water Drainage into a SiphonDraining the water into a basin Technical Data DimensionsDelivery Heads over 1m Page Index Service When do you incur costs even during the warranty period?