AEG 72330 manual Electrical Connection, Water Connection, Permissible Water Pressure

Page 45

Setting up and connection instructions

Electrical Connection

Refer to the rating plate for details of the mains voltage, current type and the necessary fuses. The rating plate is located at the top behind the filling door.

; This unit conforms to the following EU directives:

–the ”Low Voltage Directive" 73/23/EU with changes

–the ”EMC Directive" 89/336/EWG with changes

Water Connection

3The washing machine has safety features which prevent contamination of the drinking water and which conform to the legal regulations of the water authorities (e.g. for Germany: DVGW regulations). Other pro- tection measures in the installation are therefore not necessary.

Attention!

–Units for connection to cold water must not be connected to hot water!

–Use only new sets of hoses for connection!

Permissible Water Pressure

The water pressure must be at least 1bar (= 10N/cm2 = 0.1MPa), maxi- mum 10bar (= 100N/cm2 = 1MPa).

•In the case of more than 10bar: Connect a pressure-reducing valve upstream.

•In the case of less than 1bar: Unscrew the intake hose on the unit side on the inlet solenoid valve and remove the flow regulator (to do this, remove the filter with pointed pliers and remove the rubber washer behind). Replace the filter.

45

Image 45

Contents ÖKO-LAVAMAT 72330 update Tel /3630444 Dear customerContents What to do if Remedying FaultsContents Safety Before Putting into Operation for the First TimeCorrect Use General Safety Child SafetyEnvironment Tips DisposalDispose the packing material Dispose the old applianceUnit Description Front ViewDrawer for Washing Powder and Care Agent Program Selector Control PanelWoollens WOL, LAINE/P Handwash EASY-CARES KREUKHERSTELLEND, DefroissablePRE Wash VOORWAS, Prelav Additional Program ButtonsConsumption Values and Time Requirements Before the First Wash What Does Update Mean?Sort and Prepare the Washing Prepare the Washing CycleWashing Types and Care Codes How much washing detergent and care agent? Water SoftenerWater Hardness Details Brief Instructions Run a Washing CycleSet the Washing Program After the Washing Program EndsIf necessary, change the spin speed for the final Change Spin Speed / Select Rinse HoldAdd the Washing Opening and Closing the Filling DoorAdd Washing Detergent/Care Agent If using Liquid Detergent/TabsCompartment for in-wash stain treatment Compartment for pre-wash agent/soaking agentCompletion of the Washing Program Start the Washing ProgramChanging a Washing Program Program Sequence DisplayChange the Spin Speed Select the Additional ProgramWashing Cycle Ended/Remove Washing Washing Program TablesEASY-CARES PRE Wash Separate Conditioning/Starching/Impregnating Separate RinseSeparate Spin Washing Detergent Drawer Cleaning and CareFilling Door Washing DrumWhat to do if Remedying FaultsAdjust in accordance with Sans Repassage Rinsing water is Cause is probably a If the washing is grey and limescale forms in the drum If the washing result is not satisfactoryIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation When all the washing solution has drained off Clean the Solution PumpEmergency Unlocking of the Filling Door Cancel Additional Rinse Additional Rinse RINSE+/SPOELEN+/RINCAGE+Set Additional Rinse Child Safety Feature Setting the Child Safety FeatureCancelling the Child Safety Feature Safety Instructions for Installation Setting UP and Connection InstructionsSetting Up the Unit Remove the Transport SafeguardTransporting the Unit Close off the hole with the plug cap G Prepare the Installation Location Setting Up on a Concrete PedestalSetting Up on a Vibrating floor Compensate for Floor Unevenness Electrical Connection Water ConnectionPermissible Water Pressure Water Inflow Water Drainage Water Drainage into a SiphonDraining the water into a basin Technical Data DimensionsDelivery Heads over 1m Page Index When do you incur costs even during the warranty period? Service