AEG 72330 If the washing result is not satisfactory, If there are white residues on the washing

Page 34

Instructions for use

If the washing result is not satisfactory

If the washing is grey and limescale forms in the drum

•Not enough washing detergent added.

•The right washing detergent was not used.

•Special types of stain were not pretreated.

•Program or temperature incorrectly set.

•If binary wahing detergents were used, the individual components were not added in the correct ratio.

If there are still grey stains on the washing

•Washing contaminated with creams, grease or oils was washing with too little detergent.

•Washing at too low temperature.

•A frequent cause is that conditioner – particularly concentrated form, ended up on the washing. Wash out such stains as quickly as possible and carefully use the right conditioner.

If foam is still visible after the final rinse

•Modern washing detergents can still produce foam, even in the final rinse. The washing is still sufficiently rinsed.

If there are white residues on the washing

•These are the insoluble components of modern detergents. They are not the result of an insufficient rinsing effect.

Shake or brush off the washing. Perhaps in future you should turn the washing before washing it. Check the choice of detergent and use a liquid detergent if necessary.

34

Image 34

Contents ÖKO-LAVAMAT 72330 update Dear customer Tel /3630444Contents Remedying Faults What to do ifContents Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General SafetyDispose the packing material DisposalEnvironment Tips Dispose the old applianceFront View Unit DescriptionDrawer for Washing Powder and Care Agent Control Panel Program SelectorEASY-CARES KREUKHERSTELLEND, Defroissable Woollens WOL, LAINE/P HandwashAdditional Program Buttons PRE Wash VOORWAS, PrelavConsumption Values and Time Requirements What Does Update Mean? Before the First WashPrepare the Washing Cycle Sort and Prepare the WashingWashing Types and Care Codes Water Softener How much washing detergent and care agent?Water Hardness Details Set the Washing Program Run a Washing CycleBrief Instructions After the Washing Program EndsChange Spin Speed / Select Rinse Hold If necessary, change the spin speed for the finalOpening and Closing the Filling Door Add the WashingCompartment for in-wash stain treatment If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Compartment for pre-wash agent/soaking agentChanging a Washing Program Start the Washing ProgramCompletion of the Washing Program Program Sequence DisplaySelect the Additional Program Change the Spin SpeedWashing Cycle Ended/Remove Washing Program Tables WashingEASY-CARES PRE Wash Separate Rinse Separate Conditioning/Starching/ImpregnatingSeparate Spin Cleaning and Care Washing Detergent DrawerWashing Drum Filling DoorRemedying Faults What to do ifAdjust in accordance with Sans Repassage Rinsing water is Cause is probably a If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Clean the Solution Pump When all the washing solution has drained offEmergency Unlocking of the Filling Door Additional Rinse RINSE+/SPOELEN+/RINCAGE+ Cancel Additional RinseSet Additional Rinse Setting the Child Safety Feature Child Safety FeatureCancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for InstallationRemove the Transport Safeguard Setting Up the UnitTransporting the Unit Close off the hole with the plug cap G Setting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Page Index Service When do you incur costs even during the warranty period?