AEG 72330 manual Water Inflow

Page 46

Setting up and connection instructions

Water Inflow

A pressure hose 1.35m in length is supplied.

If a longer inflow hose is required, only a VDE-approved, complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible.

–Sets of hoses in lengths of 2.2m, 3.5m and 5m are available for washing machines without Aqua-Control.

–Sets of hoses in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua-Control.

Attention! Never cut into pieces in order to extend the hoses!

3Sealing rings are supplied either in the plastic nuts of the hose screw connection or in the

enclosed pack. Do not use other seals!

0 1. Connect the hose with the angled connection to the machine.

Attention!

– Do not lay the supply hose vertically downwards. Rather, turn it to the right or left as shown in the diagram.

– Only tighten the screw connection manually.

2. Connect the hose with the

straight connection to a water tap with a screw thread of R 3/4 (inches).

Attention! Only tighten the screw connection manually.

3. By slowly opening the water tap before putting the washing machine into operation, check whether the connection is free of leaks.

46

Image 46

Contents ÖKO-LAVAMAT 72330 update Dear customer Tel /3630444Contents Remedying Faults What to do ifContents Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General SafetyDispose the packing material DisposalEnvironment Tips Dispose the old applianceFront View Unit DescriptionDrawer for Washing Powder and Care Agent Control Panel Program SelectorEASY-CARES KREUKHERSTELLEND, Defroissable Woollens WOL, LAINE/P HandwashAdditional Program Buttons PRE Wash VOORWAS, PrelavConsumption Values and Time Requirements What Does Update Mean? Before the First WashPrepare the Washing Cycle Sort and Prepare the WashingWashing Types and Care Codes Water Softener How much washing detergent and care agent?Water Hardness Details Set the Washing Program Run a Washing CycleBrief Instructions After the Washing Program EndsChange Spin Speed / Select Rinse Hold If necessary, change the spin speed for the finalOpening and Closing the Filling Door Add the WashingCompartment for in-wash stain treatment If using Liquid Detergent/TabsAdd Washing Detergent/Care Agent Compartment for pre-wash agent/soaking agentChanging a Washing Program Start the Washing ProgramCompletion of the Washing Program Program Sequence DisplaySelect the Additional Program Change the Spin SpeedWashing Cycle Ended/Remove Washing Program Tables WashingEASY-CARES PRE Wash Separate Rinse Separate Conditioning/Starching/ImpregnatingSeparate Spin Cleaning and Care Washing Detergent DrawerWashing Drum Filling DoorRemedying Faults What to do ifAdjust in accordance with Sans Repassage Rinsing water is Cause is probably a If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Clean the Solution Pump When all the washing solution has drained offEmergency Unlocking of the Filling Door Additional Rinse RINSE+/SPOELEN+/RINCAGE+ Cancel Additional RinseSet Additional Rinse Setting the Child Safety Feature Child Safety FeatureCancelling the Child Safety Feature Setting UP and Connection Instructions Safety Instructions for InstallationRemove the Transport Safeguard Setting Up the UnitTransporting the Unit Close off the hole with the plug cap G Setting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Dimensions Technical DataDelivery Heads over 1m Page Index Service When do you incur costs even during the warranty period?