AEG 86740 manual Compensate for Floor Unevenness

Page 52

Setting up and connection instructions

Compensate for Floor Unevenness

3	Automatic Adjustment Foot: Your washing machine's rear left foot is
	of a spring leg design. This guarantees good stability of the unit, even

at high spinning speeds.

If the washing machine still does not stand firmly enough during spin- ning, proceed as follows:

01. Adjust the three adjustment feet

to the setpoint 10mm. To do this,

use the supplied special button to remove the transport safeguard.

If the automatic adjustment foot still does not reach the floor:

2. Manually extend the automatic adjustment foot (rear left) by the

necessary amount.

3. If necessary, check the setting with a spirit level.

Attention! Never use wood, card or similar underlays to compen-

sate for minor floor unevenness. Always use the adjustable screw-type feet of the machine.

52

Image 52

Contents ÖKO-LAVAMAT 86740 update Dear customer Contents Remedying Faults What to do ifPage Before Putting into Operation for the First Time SafetyCorrect Use Child Safety General SafetyDisposal Environmental TipsDispose the packing material For polyoxymethylene, e.g. plastic clipsFront View Unit DescriptionDrawer for Washing Powder and Care Agent Control Panel Programme knobWool WOL, LAINE/ P Hand wash program Silk ZIJDE, SOIE/ P handwashAdditional programme buttons PRE Wash VOORWAS, PRELAV. Pre wash/SoakingProgrammable functions Two levels for other programmesTemperature Consumption values and time requirementsWater Protection Aqua Control + Aqua Alarm What does Update mean?Wash Time Display Preparing a Wash Load Before the first washSorting and preparing a wash load Types of washing and care symbols How much washing detergent and care agent? Water SoftenerCarrying out a wash cycle Brief instructionsAfter completion of the wash programme Open door, remove washingSetting the wash programme Change Spin Speed / Select Rinse Hold Setting the delay timer/soaking time Delay timer Soaking durationOpening and Closing the Filling Door Putting in the washingWhen using liquid washing agent/Tabs Add Washing Detergent/Care AgentCompartment for powdered washing agent/Tabs Compartment for pre-wash agent/soaking agentFor a set delay time Starting the wash programSequence of the programme Programme sequence displayMulti display Changing speed of spinningWash cycle ended/Remove washing Remove washing Turn programme knob to OFF UIT, ArretLights up, too much washing detergent was used Programme tables WashFashion Separate Rinsing/Conditioner/Starching/Impregnation Separate SpinningCleaning and Care Washing Detergent DrawerWashing Drum Filling DoorCleaning the drain pump Before cleaning the drain pumpAfter remedying the fault, press the button Remedying FaultsWhat to do if Been removed Conditioner has not Conditioner insert Rinsed, compartment No negative effect on If the washing result is not satisfactory If the washing is grey and limescale forms in the drumIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation When all the washing solution has drained off Emergency Unlocking of the Filling DoorAid of the emergency unlocking facility Gency unlocking and remove the plug from the mainsWith more water Additional rinse cycle RINCAGE+Set additional rinse cycle Setting water cooling Cancel additional rinse cycleWater cooling Additional rinse cycle and water cooling Cancel water coolingGramme duration increase Variomatic-loose spinning Cancel loose spinSet loose spin Programme security Setting programme securityReleasing the programme security Setting the Child Safety Feature Child Safety FeatureCancelling the Child Safety Feature Setting up and connection instructions Safety Instructions for InstallationSetting Up the Unit Remove the Transport SafeguardWhen transporting the unit with a sack trolley Transporting the UnitFirmly pull both hose holders off the unit Supplied with the unitSetting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Technical Data DimensionsDelivery Heads over 1m Measurements in mmGuarantee conditions BelgiumGuarantee conditions Customer services Page Page Index Service When do you incur costs even during the warranty period?AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG