AEG 86740 manual Electrical Connection, Water Connection, Permissible Water Pressure

Page 53

Setting up and connection instructions

Electrical Connection

Refer to the rating plate for details of the mains voltage, current type and the necessary fuses. The rating plate is located at the top behind the filling door.

; This unit conforms to the following EU directives:

–the ”Low Voltage Directive" 73/23/EU with changes

–the ”EMC Directive" 89/336/EWG with changes

Water Connection

3	The washing machine has safety features which prevent contamination
	of the drinking water and which conform to the legal regulations of

the water authorities (e.g. for Germany: DVGW regulations). Other pro- tection measures in the installation are therefore not necessary.

Attention!

– Units for connection to cold water must not be connected to hot wa- ter!

– Use only new sets of hoses for connection!

Permissible Water Pressure

The water pressure must be at least 1bar (= 10N/cm2 = 0.1MPa), maxi- mum 10bar (= 100N/cm2 = 1MPa).

•In the case of more than 10bar: Connect a pressure-reducing valve upstream.

•In the case of less than 1bar: Unscrew the intake hose on the unit side on the inlet solenoid valve and remove the flow regulator (to do this, remove the filter with pointed pliers and remove the rubber washer behind). Replace the filter.

53

Image 53

Contents ÖKO-LAVAMAT 86740 update Dear customer Contents What to do if Remedying FaultsPage Correct Use SafetyBefore Putting into Operation for the First Time General Safety Child SafetyEnvironmental Tips DisposalDispose the packing material For polyoxymethylene, e.g. plastic clipsDrawer for Washing Powder and Care Agent Unit DescriptionFront View Programme knob Control PanelSilk ZIJDE, SOIE/ P handwash Wool WOL, LAINE/ P Hand wash programPRE Wash VOORWAS, PRELAV. Pre wash/Soaking Additional programme buttonsTwo levels for other programmes Programmable functionsConsumption values and time requirements TemperatureWash Time Display What does Update mean?Water Protection Aqua Control + Aqua Alarm Sorting and preparing a wash load Before the first washPreparing a Wash Load Types of washing and care symbols Water Softener How much washing detergent and care agent?Brief instructions Carrying out a wash cycleAfter completion of the wash programme Open door, remove washingSetting the wash programme Change Spin Speed / Select Rinse Hold Soaking duration Setting the delay timer/soaking time Delay timerPutting in the washing Opening and Closing the Filling DoorAdd Washing Detergent/Care Agent When using liquid washing agent/TabsCompartment for powdered washing agent/Tabs Compartment for pre-wash agent/soaking agentStarting the wash program For a set delay timeProgramme sequence display Sequence of the programmeMulti display Changing speed of spinningRemove washing Turn programme knob to OFF UIT, Arret Wash cycle ended/Remove washingLights up, too much washing detergent was used Wash Programme tablesFashion Separate Spinning Separate Rinsing/Conditioner/Starching/ImpregnationWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpWhat to do if Remedying FaultsAfter remedying the fault, press the button Been removed Conditioner has not Conditioner insert Rinsed, compartment No negative effect on If the washing is grey and limescale forms in the drum If the washing result is not satisfactoryIf there are still grey stains on the washing If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Emergency Unlocking of the Filling Door When all the washing solution has drained offAid of the emergency unlocking facility Gency unlocking and remove the plug from the mainsSet additional rinse cycle Additional rinse cycle RINCAGE+With more water Water cooling Cancel additional rinse cycleSetting water cooling Gramme duration increase Cancel water coolingAdditional rinse cycle and water cooling Set loose spin Cancel loose spinVariomatic-loose spinning Releasing the programme security Setting programme securityProgramme security Cancelling the Child Safety Feature Child Safety FeatureSetting the Child Safety Feature Safety Instructions for Installation Setting up and connection instructionsRemove the Transport Safeguard Setting Up the UnitWhen transporting the unit with a sack trolley Transporting the UnitSupplied with the unit Firmly pull both hose holders off the unitSetting Up on a Vibrating floor Prepare the Installation LocationSetting Up on a Concrete Pedestal Compensate for Floor Unevenness Permissible Water Pressure Electrical ConnectionWater Connection Water Inflow Draining the water into a basin Water DrainageWater Drainage into a Siphon Dimensions Technical DataDelivery Heads over 1m Measurements in mmBelgium Guarantee conditionsGuarantee conditions Customer services Page Page Index When do you incur costs even during the warranty period? ServiceAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG