AEG 86740 manual Water Inflow

Page 54

Setting up and connection instructions

Water Inflow

A pressure hose 1.5m in length is supplied.

If a longer inflow hose is required, only a VDE-approved, complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible.

–Sets of hoses in lengths of 2.2m, 3.5m and 5m are available for washing machines without Aqua-Control.

–Sets of hoses in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua-Control.

Attention! Never cut into pieces in order to extend the hoses!

3	Sealing rings are supplied either in the plastic
	nuts of the hose screw connection or in the en-

closed pack. Do not use other seals!

0 1. Connect the hose with the angled connection to the machine.

Attention!

– Do not lay the supply hose vertically downwards. Rather, turn it to the right or left as shown in the diagram.

– Only tighten the screw connection manually.

2. Connect the hose with the

straight connection to a water tap with a screw thread of R 3/4 (inches).

Attention! Only tighten the screw connection manually.

3. By slowly opening the water tap before putting the washing machine into operation, check whether the connection is free of leaks.

54

Image 54

Contents ÖKO-LAVAMAT 86740 update Dear customer Contents Remedying Faults What to do ifPage Safety Before Putting into Operation for the First TimeCorrect Use Child Safety General SafetyDispose the packing material DisposalEnvironmental Tips For polyoxymethylene, e.g. plastic clipsUnit Description Front ViewDrawer for Washing Powder and Care Agent Control Panel Programme knobWool WOL, LAINE/ P Hand wash program Silk ZIJDE, SOIE/ P handwashAdditional programme buttons PRE Wash VOORWAS, PRELAV. Pre wash/SoakingProgrammable functions Two levels for other programmesTemperature Consumption values and time requirementsWhat does Update mean? Water Protection Aqua Control + Aqua AlarmWash Time Display Before the first wash Preparing a Wash LoadSorting and preparing a wash load Types of washing and care symbols How much washing detergent and care agent? Water SoftenerAfter completion of the wash programme Carrying out a wash cycleBrief instructions Open door, remove washingSetting the wash programme Change Spin Speed / Select Rinse Hold Setting the delay timer/soaking time Delay timer Soaking durationOpening and Closing the Filling Door Putting in the washingCompartment for powdered washing agent/Tabs When using liquid washing agent/TabsAdd Washing Detergent/Care Agent Compartment for pre-wash agent/soaking agentFor a set delay time Starting the wash programMulti display Sequence of the programmeProgramme sequence display Changing speed of spinningWash cycle ended/Remove washing Remove washing Turn programme knob to OFF UIT, ArretLights up, too much washing detergent was used Programme tables WashFashion Separate Rinsing/Conditioner/Starching/Impregnation Separate SpinningCleaning and Care Washing Detergent DrawerWashing Drum Filling DoorCleaning the drain pump Before cleaning the drain pumpRemedying Faults After remedying the fault, press the buttonWhat to do if Been removed Conditioner has not Conditioner insert Rinsed, compartment No negative effect on If there are still grey stains on the washing If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If foam is still visible after the final rinseCarry Out an Emergency Emptying Operation Aid of the emergency unlocking facility When all the washing solution has drained offEmergency Unlocking of the Filling Door Gency unlocking and remove the plug from the mainsAdditional rinse cycle RINCAGE+ With more waterSet additional rinse cycle Cancel additional rinse cycle Setting water coolingWater cooling Cancel water cooling Additional rinse cycle and water coolingGramme duration increase Cancel loose spin Variomatic-loose spinningSet loose spin Setting programme security Programme securityReleasing the programme security Child Safety Feature Setting the Child Safety FeatureCancelling the Child Safety Feature Setting up and connection instructions Safety Instructions for InstallationWhen transporting the unit with a sack trolley Setting Up the UnitRemove the Transport Safeguard Transporting the UnitFirmly pull both hose holders off the unit Supplied with the unitPrepare the Installation Location Setting Up on a Concrete PedestalSetting Up on a Vibrating floor Compensate for Floor Unevenness Electrical Connection Water ConnectionPermissible Water Pressure Water Inflow Water Drainage Water Drainage into a SiphonDraining the water into a basin Delivery Heads over 1m Technical DataDimensions Measurements in mmGuarantee conditions BelgiumGuarantee conditions Customer services Page Page Index Service When do you incur costs even during the warranty period?AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG