AEG 86740 manual Water Drainage into a Siphon, Draining the water into a basin

Page 55

Setting up and connection instructions

Water Drainage

The drainage hose can either be connected to a siphon or hung in a wash basin or bath tub.

Only original hoses may be used for extension purposes (max. 3m on the floor and then up to 80cm high). The Customer Service stocks hoses in lengths of 2.7 and 4m.

Attention! It is absolutely essential to install the drainage hose free of pinches.

Water Drainage into a Siphon

The grommet on the end of the hose fits all commonly used siphon types.

0 Secure the grommet/siphon connecting point with a hose clamp.

Draining the water into a basin

Attention!

Small basins are not suitable for draining the water into them. Water could overflow!

It is not permitted to submerge the

end of the drainage hose into the pumped-off water. Water could be sucked up into the hose!

When hooked into a wash-basin or a

bath tub the drainage hose must be protected from slipping out of place by the supplied slip-on elbow. Other- wise the repelling power of the drain- ing water can press the hose out of the sink.

0 Fix the elbow to the water tap or to the wall with string.

55

Image 55
Contents ÖKO-LAVAMAT 86740 update Dear customer Contents What to do if Remedying FaultsPage Before Putting into Operation for the First Time SafetyCorrect Use General Safety Child SafetyFor polyoxymethylene, e.g. plastic clips DisposalEnvironmental Tips Dispose the packing materialFront View Unit DescriptionDrawer for Washing Powder and Care Agent Programme knob Control PanelSilk ZIJDE, SOIE/ P handwash Wool WOL, LAINE/ P Hand wash programPRE Wash VOORWAS, PRELAV. Pre wash/Soaking Additional programme buttonsTwo levels for other programmes Programmable functionsConsumption values and time requirements TemperatureWater Protection Aqua Control + Aqua Alarm What does Update mean?Wash Time Display Preparing a Wash Load Before the first washSorting and preparing a wash load Types of washing and care symbols Water Softener How much washing detergent and care agent?Open door, remove washing Carrying out a wash cycleBrief instructions After completion of the wash programmeSetting the wash programme Change Spin Speed / Select Rinse Hold Soaking duration Setting the delay timer/soaking time Delay timerPutting in the washing Opening and Closing the Filling DoorCompartment for pre-wash agent/soaking agent When using liquid washing agent/TabsAdd Washing Detergent/Care Agent Compartment for powdered washing agent/TabsStarting the wash program For a set delay timeChanging speed of spinning Sequence of the programmeProgramme sequence display Multi displayRemove washing Turn programme knob to OFF UIT, Arret Wash cycle ended/Remove washingLights up, too much washing detergent was used Wash Programme tablesFashion Separate Spinning Separate Rinsing/Conditioner/Starching/ImpregnationWashing Detergent Drawer Cleaning and CareFilling Door Washing DrumBefore cleaning the drain pump Cleaning the drain pumpAfter remedying the fault, press the button Remedying FaultsWhat to do if Been removed Conditioner has not Conditioner insert Rinsed, compartment No negative effect on If foam is still visible after the final rinse If the washing result is not satisfactoryIf the washing is grey and limescale forms in the drum If there are still grey stains on the washingCarry Out an Emergency Emptying Operation Gency unlocking and remove the plug from the mains When all the washing solution has drained offEmergency Unlocking of the Filling Door Aid of the emergency unlocking facilityWith more water Additional rinse cycle RINCAGE+Set additional rinse cycle Setting water cooling Cancel additional rinse cycleWater cooling Additional rinse cycle and water cooling Cancel water coolingGramme duration increase Variomatic-loose spinning Cancel loose spinSet loose spin Programme security Setting programme securityReleasing the programme security Setting the Child Safety Feature Child Safety FeatureCancelling the Child Safety Feature Safety Instructions for Installation Setting up and connection instructionsTransporting the Unit Setting Up the UnitRemove the Transport Safeguard When transporting the unit with a sack trolleySupplied with the unit Firmly pull both hose holders off the unitSetting Up on a Concrete Pedestal Prepare the Installation LocationSetting Up on a Vibrating floor Compensate for Floor Unevenness Water Connection Electrical ConnectionPermissible Water Pressure Water Inflow Water Drainage into a Siphon Water DrainageDraining the water into a basin Measurements in mm Technical DataDimensions Delivery Heads over 1mBelgium Guarantee conditionsGuarantee conditions Customer services Page Page Index When do you incur costs even during the warranty period? ServiceAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG