Beko QWM84 Installation, Appropriate installation location, Removing packaging reinforcement

Page 11
warning: Do not remove the transportation locks before taking out the packaging reinforcement.

3Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

C Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.

B warning: Installation and electrical connections of the product must be carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

A warning: Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

C Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

3.1 Appropriate installation location

•Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

•Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

•Do not place the product on the power cable.

•Do not install the product at places where temperature may fall below 0ºC.

•Place the product at least 1 cm away from the edges of other furniture.

3.2Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

3.3Removing the transportation locks

A

A warning: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

1.Loosen all the bolts with a suitable spanner until they rotate freely (C).

2.Remove transportation safety bolts by turning them gently.

3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

Washing Machine /User’s Manual

11 / EN

 

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Washing Machine Important information or useful hints about usage Dear Customer Explanation of symbolsTroubleshooting Important instructions for safety Environment4Installation Maintenance and cleaningGeneral safety Important instructions for safety and environmentIntended use Important instructions for safety and environmentDisposing of the waste product Childrens safetyPackage information Compliance with RoHS Directive Compliance with Weee DirectiveTop panel Loading door Control panel Power cableYour washing machine OverviewYour washing machine Package Contents Your washing machine Technical specifications Removing the transportation locks InstallationAppropriate installation location Removing packaging reinforcementConnecting to the drain InstallationConnecting water supply 13 / EN Adjusting the feetFitting a different plug Electrical connectionTighten all lock nuts again by hand Electricity supply15 / EN 16 / EN PreparationSorting the laundry 17 / EN Preparation Preparing laundry for washingThings to be done for energy saving Loading the laundry Preparation Initial useCorrect load capacity 19 / EN Preparation Using detergent and softenerDetergent Drawer Detergent drawer compartments are indicated belowBleaches Wipe the inside of the drum after using starchPreparation Liquid Softener Compartment21 / EN Preparation Tips for efficient washingControl panel Display symbolsSpin Speed Adjustment button On / Off button Display Operating the productMain programmes Operating the product Preparing the machineProgramme selection Operating the product Additional programmes 25 / EN Temperature selectionOperating the product Special programmes Spin speed selection26 / EN Operating the product Programme and consumption table27 / EN Operating the product28 / EN Operating the product Auxiliary function selectionPrewash Extra RinseTime display Changing the selections after programme has started Operating the product Starting the programmeProgress of programme Loading door lockChild Lock Cancelling the programmeMachine is in Rinse Hold mode 32 / EN Your machine is equipped with a Standby ModeOperating the product End of programme 33 / EN Quick User GuideMonths Cleaning the detergent drawerCleaning the loading door and the drum Has come to an endDraining remaining water and cleaning the pump filter Maintenance and cleaningCleaning the water intake filters Cleaning the body and control panel36 / EN Install the filterPlace a large container at the end of the hose Machine does not fill with water Troubleshooting37 / EN Programme cannot be started or selected38 / EN TroubleshootingIt does not rinse well 39 / ENFoam is overflowing from the detergent drawer 40 / ENDetergent residue in the detergent drawer Water pressure is low. Check the water pressureMachine does not start. Nothing appears on the display On / Off button might not be pressed. Press On / Off buttonLoading door may be open. Close the loading door 41 / EN42 / EN Complying Commission Delegated Regulation EU No 1061/20143 / EN BUILT-IN Installation44 / EN 45 / EN 46 / EN 47 / EN 48 / EN 49 / EN 50 / EN 51 / EN 52 / EN 53 / EN 54 / EN Washing Machines ServiceGuarantee
Top Page Image Contents