Beko QWM84 Electrical connection, Tighten all lock nuts again by hand, Electricity supply

Page 14

Installation

3. Tighten all lock nuts again by hand.

A warning: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

3.7 Electrical connection

Connect the product to a grounded outlet protected by a 13 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

Connection must comply with national regulations.

Power cable plug must be within easy reach after installation.

If the current value of the fuse or breaker in the house is less than 13 Amps, have a qualified electrician install a 13 Amp fuse.

The voltage specified in the "Technical specifications" section must be equal to your mains voltage.

Do not make connections via extension cables or multi-plugs.

B warning: Damaged power cables must be replaced by the Authorized Service Agents.

Electrical requirements

Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your

electricity supply.

We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position. Should the mains lead of the appliance become damaged or need replacing at any time, it must be replaced by a special purpose made mains lead which can only be obtained from a Authorised Service Agent.

B warning: This appliance must be earthed

If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted.

Destroy the old plug, which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house. The moulded plug on this appliance incorporates a 13A fuse. Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of losing the fuse cover, the plug must not be used until a replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store.

Important

Fitting a different plug

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug, proceed as follows:

1Connect the green - yellow or green (earth) wire to the terminal in the plug marked ‘E’ or with the symbol f or coloured green and yellow or green.

2Connect the blue (neutral) wire to the terminal in the plug marked ‘N’ or coloured black.

3Connect the brown (live) wire to the terminal in the plug marked ‘L’ or coloured red.

14 / EN

Washing Machine /User’s Manual

 

 

Image 14
Contents Washing Machine Dear Customer Explanation of symbols Important information or useful hints about usageMaintenance and cleaning Important instructions for safety Environment4Installation TroubleshootingImportant instructions for safety and environment General safetyImportant instructions for safety and environment Intended useDisposing of the waste product Childrens safetyPackage information Compliance with Weee Directive Compliance with RoHS DirectiveOverview Power cableYour washing machine Top panel Loading door Control panelYour washing machine Package Contents Your washing machine Technical specifications Removing packaging reinforcement InstallationAppropriate installation location Removing the transportation locksConnecting to the drain InstallationConnecting water supply Adjusting the feet 13 / ENElectricity supply Electrical connectionTighten all lock nuts again by hand Fitting a different plug15 / EN 16 / EN PreparationSorting the laundry 17 / EN Preparation Preparing laundry for washingThings to be done for energy saving Loading the laundry Preparation Initial useCorrect load capacity Detergent drawer compartments are indicated below Preparation Using detergent and softenerDetergent Drawer 19 / ENLiquid Softener Compartment Wipe the inside of the drum after using starchPreparation BleachesPreparation Tips for efficient washing 21 / ENOperating the product Display symbolsSpin Speed Adjustment button On / Off button Display Control panelMain programmes Operating the product Preparing the machineProgramme selection Operating the product Additional programmes Spin speed selection Temperature selectionOperating the product Special programmes 25 / ENOperating the product Programme and consumption table 26 / ENOperating the product 27 / ENExtra Rinse Operating the product Auxiliary function selectionPrewash 28 / ENTime display Loading door lock Operating the product Starting the programmeProgress of programme Changing the selections after programme has startedChild Lock Cancelling the programmeMachine is in Rinse Hold mode 32 / EN Your machine is equipped with a Standby ModeOperating the product End of programme Quick User Guide 33 / ENHas come to an end Cleaning the detergent drawerCleaning the loading door and the drum MonthsCleaning the body and control panel Maintenance and cleaningCleaning the water intake filters Draining remaining water and cleaning the pump filter36 / EN Install the filterPlace a large container at the end of the hose Programme cannot be started or selected Troubleshooting37 / EN Machine does not fill with waterTroubleshooting 38 / EN39 / EN It does not rinse wellWater pressure is low. Check the water pressure 40 / ENDetergent residue in the detergent drawer Foam is overflowing from the detergent drawer41 / EN On / Off button might not be pressed. Press On / Off buttonLoading door may be open. Close the loading door Machine does not start. Nothing appears on the displayComplying Commission Delegated Regulation EU No 1061/201 42 / ENBUILT-IN Installation 43 / EN44 / EN 45 / EN 46 / EN 47 / EN 48 / EN 49 / EN 50 / EN 51 / EN 52 / EN 53 / EN 54 / EN Service Washing MachinesGuarantee