Before connection
³Do not connect the AC mains lead until all other connections are complete.
³To prepare the AM loop antenna and speaker cords (and FM antenna for areas other than the United Kingdom, Continen- tal Europe, and Russia), twist the vinyl tip and pull off ([A]).
1 Flat cables.
Keep the cables as flat as possible against the back of the unit.
Note
Connect the black connectors to the black terminals and the blue connector to the blue terminal. Incorrect connection of the flat cables can damage the unit.
2 FM antenna.
Fix the other end of the antenna where reception is best.
3 AM loop antenna.
1Attach the antenna holder to the rear panel of the changer . Then clamp the antenna into the antenna holder.
2Connect the antenna to the rear panel of the tuner/ amplifi-
er.
Keep loose antenna cord away from other wires and cords.
4 Front (L/R) speaker cords.
Connect the cords to the terminals of the same colour.
Note
³To prevent damage to circuitry, never
³Be sure to connect only positive (red, blue or gray) wires to positive (i) terminals and negative (black) wires to negative (j) terminals.
5 Surround and center speaker cords.
Subwoofer cord. (Except for the United King- dom, Continental Europe, Australia and N.Z.)
6 Video cord(s).
[B]Only for the United Kingdom and Continental Europe Use the RCAJ adaptor (included) if your television has a 21- pin SCART terminal.
You do not have to connect anything to the AUDIO terminals.
[C]Except for the United Kingdom and Continental Europe
Use this connection if you have connected a VCR or Laser Disc player (á page 51 [D]). This enables you to control the
video and audio from this equipment with [INPUT SELEC- TOR] (á page 52).
(For the United Kingdom only)
READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 4 BEFORE PROCEEDING TO STEP 7.
7 AC mains lead.
[D]Insertion of connector
Even when the connector is perfectly inserted, depending on the type of inlet used, the front part of the connector may jut out as shown in the drawing.
However there is no problem using the unit.
[E]Except for the United Kingdom, Continental Europe,
Russia, Australia and N.Z.
If the power plug will not fit your socket, use the power plug adaptor (included).
Note
The included AC mains lead is for use with this unit only. Do not use it with other equipment.
For your reference:
Information you enter into the unit’s memory, except for time, remains intact for up to two weeks after the mains lead is disconnected.
Optional antenna connections
Use outdoor antennas if radio reception is poor.
FM outdoor antenna
Note
³Disconnect the FM indoor antenna.
³The antenna should be installed by a competent technician.
| use |
b FM outdoor antenna | Before |
|
Aa Tuner/amplifier
(For the United Kingdom, Continental
Europe and Russia)
A |
| 75 | ° |
|
| |
|
|
|
|
|
| |
| FM |
| ANT |
|
| |
|
|
|
|
|
| |
| AM | ANT |
|
| ||
|
|
|
|
| ||
| LOOP | c 75 | - coaxial cable | |||
| EXT | |||||
| (not included) | |||||
|
|
|
|
| ||
(Only for the United Kingdom)
Use the antenna plug adaptor (included).
(For others)
A FM ANT 75°
GND
AM ANT
LOOP
EXT
1Remove a piece of the outer vinyl insulator.
30mm
2 Twist the shield braid to expose the
core wire.
15mm
Shield braid | Core wire |
AM outdoor antenna
Run a piece of vinyl wire horizontally across a window or other con- venient location.
Note
³Leave the loop antenna connected.
³Disconnect the antenna when the unit is not in use. Do not use the antenna during an electrical storm.
a Tuner/amplifier
d AM outdoor antenna
AM ANT
LOOP
EXT
7
RQT5471