Liebert 510 616 830 Product Description and Features, Head Pressure Control Types, Fan Speed

Page 5

Introduction

1.0INTRODUCTION

1.1Product Description and Features

The Liebert condenser is low-profile direct-drive propeller fan-type air cooled unit suitable for mount- ing outdoors. It provides for the heat rejection of either one or two separate refrigeration circuits, matching heat rejection capacity varying with the outdoor ambient temperatures with each corre- sponding compressors heat rejection requirements. Constructed with an aluminum cabinet and a cop- per-tube aluminum fin coil, the unit is quiet and corrosion resistant. The condenser is quickly and easily installed, because all internal wiring is completed at the factory with only electrical connec- tions to be made at the job site. All electrical connections and controls are enclosed in an integral weatherproof section of the condenser.

Figure 1 Liebert two-fan condenser

1.2Head Pressure Control Types

1.2.1Fan Speed

Fan speed control utilizes a wave-chopper control to vary the air volume over the condenser coil, based on refrigerant head pressure. The fan motor next to the electrical panel (two fans on 6-fan and 8-fan models) is a single-phase, permanent split capacitor motor with motor speed adjusted in response to refrigerant pressure. The balance of fans on multi-fan units cycle on ambient thermostats. The control system provides refrigerant head pressure control for outdoor ambients as low as -20°F (-28.9 °C).

1.2.2Variable Frequency Drive

VFD Condenser control system utilizes a variable frequency drive, inverter duty fan motor operating from 0% to 100% motor RPM based on head pressure, sensed by refrigerant pressure transducers. VFD, ambient-temperature thermostat(s), motor overload protection and electrical control circuit are factory-wired in the integral control panel. VFD controls the fan adjacent to the connection end of the condenser and remains energized with active compressor operation. The balance of fans on multi-fan units cycle on ambient thermostats. This system provides refrigerant head pressure control for out- door ambients as low as -20°F (-28.9°C).

1

Image 5
Contents Liebert Air Cooled, Direct Drive Condensers Example DCDF165-Y Three-phase voltage is only voltage available as standardOn condensers with VFD Control, Lee-temp receivers, Fan Speed Control 2-8 fan models onlyTable of Contents Operation System MaintenanceHead Pressure Control Types Product Description and FeaturesFan Speed Variable Frequency DriveTransient Voltage Surge Suppression Option Typical System ConfigurationsSound Level Options Lee-Temp Discharge Fan Speed and VFDSite Considerations Dimensions and Weights1067 mm See for typical condenser footprint dimensionsFour-Fan41-3/16 Condenser 1046mm See for typical Operation and component accessCondenser footprint dimensions Typical condenser footprint-dimensions Piping connections for 6- and 8-fan Fan Speed Condensers Site Preparation Quiet-Line Models Condenser physical dataR-407C refrigerant required, approximate Refrigerant Planning ValuesReceiver Quiet-Line Condenser ModelsPacking Material Equipment InspectionUnpacking the Unit Handling Unit on the SkidRemoving the Skid and Attaching Slings Step Attaching legs to a 6-fan or 8-fan unitAttaching sling to a 6-fan or 8-fan unit for moving Mounting the CondenserElectrical Supply Preparation Line Voltage Wiring50Hz condenser full load amp values 60Hz condenser dataLow Voltage Monitoring Wiring-TCDV Only Low Voltage Control WiringElectrical Connections Lee-Temp receiver electrical data, 50Hz and 60HzVFD Control Condensers Tcdv only Wye-Connected Power SupplyDelta-Connected Power Supply Disconnect EMC Filter for Delta-Connected Power Electrical Field Connection Descriptions Electric service connection and fuse blockElectrical field connections for VFD control condensers Inspection and Installation Piping Guidelines Refrigeration Piping ConnectionsVFD and Fan Speed Control condenser piping Field Piping InstallationLee-Temp head pressure control condenser piping General arrangement-Air cooled models with Lee-Temp control Single Circuit ShownSystem Dehydration/Leak Test and Charging Procedures Electrical Moving and Placing EquipmentPiping OtherStartup Startup ChecklistSystem Maintenance General ProceduresCondenser Cleaning Special ProceduresWhen to Clean How to CleanMonthly Semiannually Condenser Maintenance Inspection ChecklistCondenser Electrical Panel Condenser Electric Panel Fan MotorsSymptom Possible Cause Check or Remedy TroubleshootingSystem Maintenance System Maintenance Page Iti Ne tTi n That