Liebert 510 616 830, 205 251, 104 165, 1010 Moving and Placing Equipment, Electrical, Piping, Other

Page 35

Checklist for Completed Installation

4.0CHECKLIST FOR COMPLETED INSTALLATION

4.1Moving and Placing Equipment

___ 1. Unpack and check received material

___ 2. Proper clearance for service access has been maintained around the equipment

___ 3. Equipment is level and mounting fasteners are tight

4.2Electrical

___ 1. Line voltage connected and matches equipment nameplate

___ 2. Power line circuit breakers or fuses have proper ratings for equipment installed

___ 3. Control wiring connections completed between indoor cooling unit and condenser

___ 4. All internal and external high and low voltage wiring connections are tight

___ 5. TCDV condensers only—Check for Delta-Connected Power Supply and make any needed adjustments per 3.7.1 - VFD Control Condensers (TCDV) only

___ 6. Monitoring wiring connections completed, when equipped, to indoor cooling unit or external monitoring panel

___ 7. Confirm that unit is properly grounded to an earth ground

___ 8. Control transformer setting matches incoming power

___ 9. Electrical service conforms to national and local codes

___ 10. Check fans for proper phase rotation. Blades should rotate clockwise when viewing the unit from the fan guard side.

4.3Piping

___ 1. Piping is completed to corresponding indoor cooling unit refrigeration circuit.

___ 2. Piping leak-checked, evacuated and charged.

___ 3. Piping is properly sized, sloped and trapped for proper oil return.

___ 4. Piping is routed to reduce potential of rub-through or chaffing.

4.4Other

___ 1. Fans rotate freely and in proper direction

___ 2. Adjust ambient thermostat setpoints to match setpoints on the electrical schematic supplied with the condenser.

___ 3. Foreign material removed from in and around all equipment installed (construction materials, construction debris, etc.).

___ 4. Installation materials and tools have been removed from in and around all equipment (literature, shipping materials, tools, etc.).

___ 5. Blank start-up sheet located, ready for completion by installer or start-up technician.

31

Image 35
Contents Liebert Air Cooled, Direct Drive Condensers Fan Speed Control 2-8 fan models only Three-phase voltage is only voltage available as standardExample DCDF165-Y On condensers with VFD Control, Lee-temp receivers,Table of Contents Operation System MaintenanceVariable Frequency Drive Product Description and FeaturesHead Pressure Control Types Fan SpeedTransient Voltage Surge Suppression Option Typical System ConfigurationsSound Level Options Lee-Temp Discharge Fan Speed and VFDSite Considerations Dimensions and Weights1067 mm See for typical condenser footprint dimensionsFour-Fan41-3/16 Condenser 1046mm See for typical Operation and component accessCondenser footprint dimensions Typical condenser footprint-dimensions Piping connections for 6- and 8-fan Fan Speed Condensers Site Preparation Quiet-Line Models Condenser physical dataQuiet-Line Condenser Models Refrigerant Planning ValuesR-407C refrigerant required, approximate ReceiverPacking Material Equipment InspectionUnpacking the Unit Handling Unit on the SkidRemoving the Skid and Attaching Slings Step Attaching legs to a 6-fan or 8-fan unitAttaching sling to a 6-fan or 8-fan unit for moving Mounting the CondenserElectrical Supply Preparation Line Voltage Wiring50Hz condenser full load amp values 60Hz condenser dataLee-Temp receiver electrical data, 50Hz and 60Hz Low Voltage Control WiringLow Voltage Monitoring Wiring-TCDV Only Electrical ConnectionsVFD Control Condensers Tcdv only Wye-Connected Power SupplyDelta-Connected Power Supply Disconnect EMC Filter for Delta-Connected Power Electrical Field Connection Descriptions Electric service connection and fuse blockElectrical field connections for VFD control condensers Inspection and Installation Piping Guidelines Refrigeration Piping ConnectionsVFD and Fan Speed Control condenser piping Field Piping InstallationLee-Temp head pressure control condenser piping General arrangement-Air cooled models with Lee-Temp control Single Circuit ShownSystem Dehydration/Leak Test and Charging Procedures Other Moving and Placing EquipmentElectrical PipingStartup Startup ChecklistSystem Maintenance General ProceduresHow to Clean Special ProceduresCondenser Cleaning When to CleanFan Motors Maintenance Inspection ChecklistMonthly Semiannually Condenser Condenser Electrical Panel Condenser Electric PanelSymptom Possible Cause Check or Remedy TroubleshootingSystem Maintenance System Maintenance Page That Ne tIti Ti n