Maytag W10150661A If using an existing vent system, If this is a new vent system Vent material

Page 9

If using an existing vent system

Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

If this is a new vent system

Vent material

Use a heavy metal vent. Do not use plastic or metal foil vent.

4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

4"

10.2 cm

4" (10.2 cm) heavy metal exhaust vent

Vent products can be purchased from your dealer or by calling Maytag Services. For more information, see the “Assistance or Service” section.

Rigid metal vent

For best drying performance, rigid metal vents are recommended.

Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

Flexible metal vents are acceptable only if accessible for cleaning.

Flexible metal vent must be fully extended and supported when the dryer is in its final location.

Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

GoodBetter

Clamps

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

B

A

4"

(10.2 cm)

4" (10.2 cm)

A. Louvered hood style

B. Box hood style

The angled hood style (shown here) is acceptable.

4"

(10.2 cm)

2½" (6.4 cm)

An exhaust hood should cap the vent to keep rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

Housecleaning problems and health problems.

9

Image 9
Contents W10150660A Sécheuse À GAZ Bravostm Avec Système DE Soin DES TissusTable DES Matières Table of ContentsYour safety and the safety of others are very important Dryer SafetyImportant Safety Instructions Installation Instructions Tools and PartsLocation Requirements Mobile home Additional installation requirements Installation Clearances Mobile home installations require Dryer DimensionsGas Supply Requirements Electrical RequirementsGas Type Gas Supply LineGas supply connection requirements Venting RequirementsBurner Input Requirements Dryer Gas PipeIf this is a new vent system Vent material If using an existing vent systemPlan Vent System Special provisions for mobile home installationsInstall Leveling Legs Install Vent SystemVent system chart Determine vent pathMake Gas Connection Connect VentLevel Dryer Reinstall the door Remove the door assemblyReverse Door Swing Reverse the strikeInstall these screws first If the dryer will not start, check the following Complete InstallationStarting Your Dryer Dryer USEDrying and Cycle Tips Stopping, Pausing or RestartingTo stop or pause your dryer at any time To restart the dryerCycles Status LightsModifiers End of Cycle Signal OptionsChanging Cycles, Modifiers and Options Drying Rack Option Rack Dry Setting Temp Time Wool SweatersTo use the drying rack Stuffed toys or pillowsCleaning the Lint Screen Cleaning the Dryer LocationCleaning the Dryer Interior Dryer CareRemoving Accumulated Lint Vacation and Moving CareChanging the Drum Light Troubleshooting Dryer OperationDryer Results Lint on load Cycle time too shortStains on load or drum Loads are wrinkledAccessories Assistance or ServiceU.S.A CanadaONE Year Limited Warranty Maytag Corporation Major Appliance WarrantyPage Votre sécurité et celle des autres est très importante Sécurité DE LA SécheuseImportantes Instructions DE Sécurité Instructions D’INSTALLATION Exigences d’emplacementOutillage et pièces Dimensions de la sécheuse Linstallation dans une maison mobile exigeDégagements de séparation à respecter Alimentation en gaz Spécifications électriquesType de gaz Gaz naturelExigences concernant le raccordement au gaz Canalisation d’arrivée de gazCaractéristiques d’alimentation du brûleur Canalisation d’arrivée de gaz de la sécheuseEn cas dutilisation du système dévacuation existant Exigences concernant lévacuationÉvacuation Planification du système d’évacuationAutres installations où le dégagement est réduit Déterminer litinéraire dacheminement du conduitTableau des systèmes dévacuation Installation des pieds de nivellement Installation du système d’évacuationRaccordement au gaz Pour utilisation dans une maison mobileRéglage de laplomb de la sécheuse Raccordement du conduit d’évacuationInversion du sens douverture de la porte Dépose de la porteInversion de la gâche Réinstallation de la porte Si la sécheuse ne démarre pas, vérifier ce qui suit Achever l’installationMise en marche de la sécheuse Utilisation DE LA SécheuseArrêt, pause ou remise en marche Pour mettre la sécheuse en pause ou larrêter à tout momentPour remettre la sécheuse en marche Témoins lumineux Conseils pour le séchage et les programmesProgrammes Modificateurs Signal de fin de programme Option de grille de séchage Modification des préréglages de niveau de séchageUtilisation de la grille de séchage Nettoyage de lemplacement de la sécheuse Entretien DE LA SécheuseNettoyage du filtre à charpie Retrait de la charpie accumulée Nettoyage de l’intérieur de la sécheuseDéménagement Changement de l’ampoule d’éclairage du tambourDépannage Fonctionnement de la sécheuseRésultats de la sécheuse Charpie sur la charge Temps de programme trop courtTaches sur la charge ou sur le tambour Charges avec faux plisAccessoires Assistance OU ServiceAu Canada Si vous avez besoin de pièces de rechangeGarantie DES Gros Appareils Ménagers Maytag Corporation W10150660A SP PN W10150661A