Teledyne 465M instruction manual Introduction, Preface

Page 11

1. INTRODUCTION

1.1.Preface

Teledyne API is pleased that you have purchased the M465M. We offer a full one year warranty (see Section 2.2) and we at Teledyne API will be pleased to provide you with any support required so that you may utilize our equipment to the fullest extent.

We hope you will not experience any problems with the Teledyne API Model 465M (M465M) but if you do, the built-in tests and diagnostics should allow you to quickly and easily find the problem. In addition, our full time customer service department is always available to answer your questions.

Teledyne API, Customer Service,

9480 Carroll Park Drive

San Diego, California 92121-5201USA

Toll-free Phone: 800-324-5190

Phone: 858-657-9800

Fax: 858-657-9816

Email: api-sales@teledyne.com

Website: http://www.Teledyne-API.com

P/N 06160D DCN6409 Teledyne API Model 465M O3 Monitor Instruction Manual - Page 9

Image 11

Contents Model 465M Ozone Monitor This page is Intentionally Left Blank General Safety Hazard Safety MessagesMise EN Garde Consignes DE SécuritéWarranty This page is Intentionally Left Blank Table of Contents Calibration Figures Tables Preface IntroductionThis page is Intentionally Left Blank Specifications Specifications and Agency ApprovalsOther Type Certifications SafetyApprovals EMC3   Principle of OperationPage Area Minimum required clearance Mechanical Installation for Nema 4X EnclosureGetting Started Ventilation ClearanceM465M Mounting Hole Locations and Dimensions Mechanical Installation 19 Rack VersionAC Power Connection for Monitors in Nema 4X Enclosures Nema AC Power Connection to Monitor Pneumatic Connections Pneumatic Connections, Rack Mount ConfigurationOzone Inlet Connection Pneumatic Connections, Nema ConfigurationRear Panel Electrical I/O Connections Exhaust ConnectionNema Electrical I/O Connections Analog Output Location of I/O Connectors in the Nema ConfigurationElectrical I/O Connections Status Name Normal Operating Output # State Status OutputsNormal Operating State Hi-Current Relay OutputsDigital Serial Interfaces Relay # FunctionEthernet Connection Frequently Asked Questions This page is Intentionally Left Blank Rack Mount Slides Low Flow AlarmOptional Hardware and Software This page is Intentionally Left Blank Menu Navigation Keypad OperationFront Panel Overview Ozone Concentration DisplayStatus LED Normal State Concentration Alarm Status/ResetAlarm Status LED Color Alarm State Status LED’sEditing Numeric Values Front Panel MenusMenu Navigation Basics Front Panel Menu Diagram Front Panel Menu Diagram Point 5V Output MA Output Diag MenuZero Calibration Signal Name Rear Panel Label FunctionSpan Calibration Parameter Meaning Units Normal Range View MenuRange SETUP-VARS MenuMeaning Default Value Property Meaning Default Range Value SETUP-ALARM MenuConfig Menu This page is Intentionally Left Blank Digital Communications Overview Changing COM port Hardware ConfigurationDigital Communications RS232 Configuration Property Value RS-232 ConfigurationFunction DB-9 General I/O Connector Pin SW2 DTE SW2 DCE Function DB-9 General I/O Connector Pin SW2 DCE RS-485 ConfigurationLink LED Left Side Activity LED Right Side Color Meaning Ethernet ConfigurationHardware Setup for Configuring the Ethernet Module Verifying Network Hardware ConnectionManually Assigning a Static IP Address Determining a Dynamically Assigned IP Address Dhcp ModePage Decimal Star Address Description Register Type Bit Bits Instrument Setup and Configuration Registers Read / WriteModbus Register Maps Real-Time Concentration and Status Registers Read OnlyMaintenance Item Recommended Interval Section MaintenanceMaintenance Schedule Instrument Layout Instrument Layout, Rack Mount ConfigurationInstrument Layout, Nema Configuration Replacing Internal Particulate Filter Internal Particulate Filter Replacement 1150 mV UV Lamp AdjustmentUV Lamp Replacement Auto-Zero Valve Replacement Sample Pump ReplacementConfiguring the Analog Output Zero Cleaning Exterior Surfaces of the M465MBoot Loader Software Setup Boot Loader OperationBoot Loader Hardware Setup Upload Firmware Page Reference Drawings TroubleshootingPneumatic Diagram Pneumatic Diagram Nema Version with Sample Conditioner Interconnect DiagramInterconnect Diagram Status LED/Output Definitions Check Lamp Pneumatic ErrorSensor OK Invalid ReadingPressure Too High Factory Calibration CalibrationThis page is Intentionally Left Blank Technical Assistance This page is Intentionally Left Blank 13. M465M Spare Parts Spare Parts List for Rack Mount VersionSpare Parts List for Nema Version