Teledyne 465M instruction manual Getting Started, Mechanical Installation for Nema 4X Enclosure

Page 17

4. GETTING STARTED

The M465M is shipped with the following standard equipment:

1.Power cord (Rack mount version only)

2.Instruction manual.

Upon receiving the M465M please do the following:

1.Verify that there is no apparent shipping damage. (If damage has occurred please advise shipper first, then Teledyne API.)

4.1.Mechanical Installation (for NEMA 4X Enclosure)

Mount the enclosure securely to a vertical surface.

Figure 4-1shows the locations of the four mounting holes.

All four mounting holes should be used to secure the monitor.

Use stainless steel, 5/16” diameter bolts.

4.1.1.Ventilation Clearance

When installing the M465M be sure to leave sufficient ventilation clearance.

Table 4-1: M465M Ventilation Clearances, NEMA Version

Area

Minimum required clearance

Back of the monitor

None

Sides of the monitor

1 inch

Above and below the monitor

1 inch

P/N 06160D DCN6409 Teledyne API Model 465M O3 Monitor Instruction Manual - Page 15

Image 17
Contents Model 465M Ozone Monitor This page is Intentionally Left Blank General Safety Hazard Safety MessagesMise EN Garde Consignes DE SécuritéWarranty This page is Intentionally Left Blank Table of Contents Calibration Figures Tables Preface IntroductionThis page is Intentionally Left Blank Specifications Specifications and Agency ApprovalsApprovals SafetyEMC Other Type Certifications3   Principle of OperationPage Getting Started Mechanical Installation for Nema 4X EnclosureVentilation Clearance Area Minimum required clearanceM465M Mounting Hole Locations and Dimensions Mechanical Installation 19 Rack VersionAC Power Connection for Monitors in Nema 4X Enclosures Nema AC Power Connection to Monitor Pneumatic Connections Pneumatic Connections, Rack Mount ConfigurationOzone Inlet Connection Pneumatic Connections, Nema ConfigurationRear Panel Electrical I/O Connections Exhaust ConnectionNema Electrical I/O Connections Analog Output Location of I/O Connectors in the Nema ConfigurationElectrical I/O Connections Status Name Normal Operating Output # State Status OutputsDigital Serial Interfaces Hi-Current Relay OutputsRelay # Function Normal Operating StateEthernet Connection Frequently Asked Questions This page is Intentionally Left Blank Rack Mount Slides Low Flow AlarmOptional Hardware and Software This page is Intentionally Left Blank Front Panel Overview OperationOzone Concentration Display Menu Navigation KeypadAlarm Status LED Color Alarm State Concentration Alarm Status/ResetStatus LED’s Status LED Normal StateEditing Numeric Values Front Panel MenusMenu Navigation Basics Front Panel Menu Diagram Front Panel Menu Diagram Point 5V Output MA Output Diag MenuZero Calibration Signal Name Rear Panel Label FunctionSpan Calibration Parameter Meaning Units Normal Range View MenuRange SETUP-VARS MenuMeaning Default Value Property Meaning Default Range Value SETUP-ALARM MenuConfig Menu This page is Intentionally Left Blank Digital Communications Overview Changing COM port Hardware ConfigurationDigital Communications RS232 Configuration Property Value RS-232 ConfigurationFunction DB-9 General I/O Connector Pin SW2 DTE SW2 DCE Function DB-9 General I/O Connector Pin SW2 DCE RS-485 ConfigurationHardware Setup for Configuring the Ethernet Module Ethernet ConfigurationVerifying Network Hardware Connection Link LED Left Side Activity LED Right Side Color MeaningManually Assigning a Static IP Address Determining a Dynamically Assigned IP Address Dhcp ModePage Modbus Register Maps Instrument Setup and Configuration Registers Read / WriteReal-Time Concentration and Status Registers Read Only Decimal Star Address Description Register Type Bit BitsMaintenance Item Recommended Interval Section MaintenanceMaintenance Schedule Instrument Layout Instrument Layout, Rack Mount ConfigurationInstrument Layout, Nema Configuration Replacing Internal Particulate Filter Internal Particulate Filter Replacement 1150 mV UV Lamp AdjustmentUV Lamp Replacement Auto-Zero Valve Replacement Sample Pump ReplacementConfiguring the Analog Output Zero Cleaning Exterior Surfaces of the M465MBoot Loader Software Setup Boot Loader OperationBoot Loader Hardware Setup Upload Firmware Page Reference Drawings TroubleshootingPneumatic Diagram Pneumatic Diagram Nema Version with Sample Conditioner Interconnect DiagramInterconnect Diagram Status LED/Output Definitions Sensor OK Pneumatic ErrorInvalid Reading Check LampPressure Too High Factory Calibration CalibrationThis page is Intentionally Left Blank Technical Assistance This page is Intentionally Left Blank 13. M465M Spare Parts Spare Parts List for Rack Mount VersionSpare Parts List for Nema Version