Teledyne 465M instruction manual Technical Assistance

Page 73

12. TECHNICAL ASSISTANCE

If this manual does not solve your problems, technical assistance may be obtained from:

Teledyne API, Customer Service,

9480 Carroll Park Drive

San Diego, California 92121-5201USA

Toll-free Phone: 800-324-5190

Phone: 858-657-9800

Fax: 858-657-9816

Email: api-sales@teledyne.com

Website: http://www.Teledyne-API.com

Before you contact Teledyne Instruments’ Customer service, fill out the problem report form in Appendix C, which is also available online for electronic submission at http://www.Teledyne-API.com/forms.

P/N 06160D DCN6409 Teledyne API Model 465M O3 Monitor Instruction Manual - Page 71

Image 73

Contents Model 465M Ozone Monitor This page is Intentionally Left Blank General Safety Hazard Safety MessagesMise EN Garde Consignes DE SécuritéWarranty This page is Intentionally Left Blank Table of Contents Calibration Figures Tables Preface IntroductionThis page is Intentionally Left Blank Specifications Specifications and Agency ApprovalsApprovals SafetyEMC Other Type Certifications3   Principle of OperationPage Getting Started Mechanical Installation for Nema 4X EnclosureVentilation Clearance Area Minimum required clearanceM465M Mounting Hole Locations and Dimensions Mechanical Installation 19 Rack VersionAC Power Connection for Monitors in Nema 4X Enclosures Nema AC Power Connection to Monitor Pneumatic Connections Pneumatic Connections, Rack Mount ConfigurationOzone Inlet Connection Pneumatic Connections, Nema ConfigurationRear Panel Electrical I/O Connections Exhaust ConnectionNema Electrical I/O Connections Electrical I/O Connections Location of I/O Connectors in the Nema ConfigurationAnalog Output Status Name Normal Operating Output # State Status OutputsDigital Serial Interfaces Hi-Current Relay OutputsRelay # Function Normal Operating StateEthernet Connection Frequently Asked Questions This page is Intentionally Left Blank Optional Hardware and Software Low Flow AlarmRack Mount Slides This page is Intentionally Left Blank Front Panel Overview OperationOzone Concentration Display Menu Navigation KeypadAlarm Status LED Color Alarm State Concentration Alarm Status/ResetStatus LED’s Status LED Normal StateMenu Navigation Basics Front Panel MenusEditing Numeric Values Front Panel Menu Diagram Front Panel Menu Diagram Point 5V Output MA Output Diag MenuZero Calibration Signal Name Rear Panel Label FunctionSpan Calibration Parameter Meaning Units Normal Range View MenuMeaning Default Value SETUP-VARS MenuRange Config Menu SETUP-ALARM MenuProperty Meaning Default Range Value This page is Intentionally Left Blank Digital Communications Changing COM port Hardware ConfigurationDigital Communications Overview RS232 Configuration Function DB-9 General I/O Connector Pin SW2 DTE SW2 DCE RS-232 ConfigurationProperty Value Function DB-9 General I/O Connector Pin SW2 DCE RS-485 ConfigurationHardware Setup for Configuring the Ethernet Module Ethernet ConfigurationVerifying Network Hardware Connection Link LED Left Side Activity LED Right Side Color MeaningManually Assigning a Static IP Address Determining a Dynamically Assigned IP Address Dhcp ModePage Modbus Register Maps Instrument Setup and Configuration Registers Read / WriteReal-Time Concentration and Status Registers Read Only Decimal Star Address Description Register Type Bit BitsMaintenance Schedule MaintenanceMaintenance Item Recommended Interval Section Instrument Layout Instrument Layout, Rack Mount ConfigurationInstrument Layout, Nema Configuration Replacing Internal Particulate Filter Internal Particulate Filter Replacement UV Lamp Replacement UV Lamp Adjustment1150 mV Auto-Zero Valve Replacement Sample Pump ReplacementConfiguring the Analog Output Zero Cleaning Exterior Surfaces of the M465MBoot Loader Hardware Setup Boot Loader OperationBoot Loader Software Setup Upload Firmware Page Pneumatic Diagram TroubleshootingReference Drawings Pneumatic Diagram Nema Version with Sample Conditioner Interconnect DiagramInterconnect Diagram Status LED/Output Definitions Sensor OK Pneumatic ErrorInvalid Reading Check LampPressure Too High Factory Calibration CalibrationThis page is Intentionally Left Blank Technical Assistance This page is Intentionally Left Blank 13. M465M Spare Parts Spare Parts List for Rack Mount VersionSpare Parts List for Nema Version