Standard Horizon CP150C owner manual Serial Ports, Card Test, Card Connector, Change Parameters

Page 46

C-CARD Test

To test the C-CARD. There are three possible situations:

1.if there is a C-CARD inserted in the slot and there is not a malfunction, the name of the C-CARD zone and the message "OK" are shown.

2.if there is a C-CARD inserted in the slot, but it is a defective C-CARD, the name of the C-CARD zone and the message "Faulty" are shown.

3.if there is not any C-CARD inserted in the slot, the message "not present" is shown.

C-CARD Connector

Indicates if there is a malfunction in the connector.

3.14.0.3 Serial Ports

If you are having problems receiving data from the position-finding instrument, this test should help determine the problem.

Figure 3.14.0.3 - Serial Ports Menu

Change Parameters

To change the parameters of the serial interface. This menu allows to select the Port (Signal Source) between EXT.PORT or DIFF.INPUT, the Baud Rate between 300, 1200, 2400, 4800 or 9600, the Data Bits (Word Length) between 7 or 8, the Parity between even, odd or none, the Stop Bits between 1 or 2, the Polarity between "+" or "-". Default settings are: Port = EXT.PORT, Baud Rate = 4800, Data Bits = 8, Parity = none, Stop Bits = 1, Polarity = +.

Input Data Display

To allow the chart plotter to act as a computer terminal and display the incoming data exactly as it is received.

If the data displayed on the screen is unrecognizable, you may have selected the wrong input parameters for your particular receiver, for example, Baud Rate 9600 instead of Baud Rate 4800. Check your receiver manual to be sure that you have selected the proper parameter. If the screen is blank, you may have a broken connection, and no data is being received or you may have connected the device to the other input port.

Use “ZOOM IN” to stop (or continue after pause) data displaying, “ENTER” to show data in hex or ASCII mode (normal or small) and “CLEAR” to exit.

Page 48		GPS Chart 150C

Image 46

Contents CP150C Table of Contents MOB Function Index FCC Compliance Statement GPS Chart 150C General Information Packing ListOptions BracketInstalling the Chart Plotter Getting StartedInstalling the Antenna Connecting PowerPower On Optional C-MAP NT+ Cartography Inserting the C-CARDControls and Indicators Controls and ConnectionsKeys ShuttlePoint knobKey and Lamp/Contrast KeyCard slot Adjusting Cursor Speed GPS Antenna connector Power and I/O connectorTurning Power on and OFF Changing Ship IconsChanging the Display Palette Adjusting the TimeChanging Light and Contrast Entering in a Mark from a Position Navigating to a MarkEntering Loran TD’S Press Menu + Advanced Setup + Enter + Navigate + Enter +Transfer Marks from PC or Other GPS Customizing Data Windows on Chart Selecting North UP or Course UPCustomizing Data box Selecting Data Window layoutCustomizing Data Windows on ANY Pages Home Mode VS. Cursor ModeCursor Mode Selecting pagesHome Mode Chart Navigation DataHighway CelestialGPS Status VHF Radio DSC LOGNmea Display Pages DisplayDepth Trend DataSelection Creating a New Mark Creating and Using MarksMarks Editing a MarkDeleting a Mark Moving a MarkDeleting a Waypoint Creating and Using RoutesCreating a new Route Locating a MarkMoving a Waypoint 1 Deleting WaypointInserting a Waypoint into a Route 2a Moving WaypointEditing a Waypoint 3b Placing Waypoint between two existing onesRoute Report page Information on a Route 4b Edit WaypointUser Points List page Information on Waypoints Menu + User Points List + EnterAllows locating selected point on the Chart Deleting a Route Selecting Route Color Following a RouteReversing a Route Goto FunctionMOB Function Selecting Time and Distance Deleting MOBTrack Plotter Fuctions Selecting a track line colorDisplaying track MaintenanceSaving a track to memory Deleting trackDisplay Resolution 320 x 240 pixels Cartography SpecificationsOperating temperature range 0/+55 degrees Celsius 13.0GPS Receiver Specifications 13.1GPS Antenna SpecificationsRAM Test Technical 3.14.0System TestRAM Menu RAM ClearContrast DIM MenuCartridges BacklightCard Test Card ConnectorSerial Ports Change ParametersNmea Input/Output Setup of Nmea output sentences NMEA2 Rtcm Input Dual Station Operation Master SlaveTerms and Functions 3.15.0User Points Handling functions 15.0 User Points iconsDestination point MarksWaypoints and Routes Route FollowingInformation on User Points User Points ListRoute Report 15.1Track History15.2Input/Output GPS DataInstruments Data Data Window on ChartData Display NMEA-0183 output Autopilot outputNavigation 15.3.1 GPS StatusOther pages About 15.4User Settings15.3.3 3D Highway Display Map CustomizationMarine Settings Display SettingsCustomize Map Depth Settings Land Settings Chart SettingsGeneral Setup Map Orientation 15.4.4 FixNavigate Coordinate SystemCompass AlarmsInternal GPS Setup Input / OutputGPS Chart 150C Simulation Automatic Info15.5.0Info Tree and Expanded Info pages Info function Getting Port Info15.5.3Getting Tide Info To display the Tide Graph page press Enter15.6Find Function Port ServicesPorts Tide stations Searching by listSearching by name WrecksIndex GPS Position Request Call