Intel II manual Removing a Hot-swap Bay Fan, Installing a Hot-swap Bay Fan

Page 41

Removing a Hot-swap Bay Fan

A

OM07042

Figure 26. Removing the Hot-swap Bay Fan Bracket

1.Observe the safety and ESD precautions at the beginning this chapter.

2.Remove the side cover.

3.Disconnect the fan’s power cable from the SCSI backplane.

4.Snap the fan out of the plastic shroud.

Installing a Hot-swap Bay Fan

1.Position the fan, label side facing away from the hot-swap bay, and snap it into the shroud.

2.Connect the fan’s power cable to the SCSI backplane (a fan in the bottom of the shroud connects to the Fan 1 header; a fan in the top of the shroud connects to Fan 0 header).

3.Reinstall the side cover.

Working Inside the System

41

Image 41

Contents Intel Astor II Server Chassis Subassembly Product Guide FCC Declaration of Conformity Contents Equipment Log and Worksheets Technical ReferenceRegulatory Information Figures WarrantyTables Feature Summary Kit ContentsFront Controls and Indicators Chassis Front Controls and IndicatorsBack I/O Ports and Features Chassis Back I/O Ports and FeaturesChassis Side View Chassis Side ViewExternal Bay for 5.25-inch Removable Media Devices PeripheralsInternal Bay for 3.5-inch IDE Hard Drives Hot-swap BaySystem Cooling Power SupplyChecking the Power Cord Monitoring System SecurityMechanical Locks Intel Astor II Server Chassis Subassembly Product Guide Tools and Supplies Needed Safety Before You Remove the Side CoverRemoving the Side Cover Removing the Side Cover Installing Chassis FeetRemoving the Hot-swap Bay Removing the Hot-swap BayDisconnect Cables and Remove Screws Removing the IDE Drive BayIDE Hard Drive Bay Rubber Bumper and Standoff Clip Placement Installing Server Board Clips and BumpersShield Installing the Server BoardInstalling the Server Board typical board shown Installing a Chassis Intrusion Switch Installing a Chassis Intrusion SwitchRemoving the Front Cover Removing the Front CoverRemoving the Diskette Drive Installing the Diskette DriveHard Drives Installing a Hard Drive into the IDE drive bayDrive Cabling Considerations IDE RequirementsIDE Hard Drive Removing a Hard Drive from the IDE Drive BayInstalling the IDE Drive Bay Remove Filler Panels and EMI Shields Installing a 5.25-inch Peripheral DeviceSnap-in Plastic Slide Rails Removing a 5.25-inch Peripheral Device Installing a Removable Media DeviceInstalling an Add-in Board Installing the Front CoverInstalling the Hot-swap Bay Removing an Add-in Board Installing an Add-in BoardInstalling the Side Cover Mounting a Scsi SCA2 Hard Disk Drive in a Plastic Carrier Hot-swap BayScsi Hard Disk Drives Hard Disk Drive and Plastic Carrier Installing a Scsi SCA2 Hard Disk Drive in the Hot-swap BayHot-swapping a Scsi SCA2 Hard Disk Drive Installing a Hard Disk DriveRemoving the Front Fan Fan Cable Connector PinoutFans Installing the Front Fan Installing the Front FanRemoving a Hot-swap Bay Fan Installing a Hot-swap Bay FanRemoving the Scsi Backplane Hot-swap BackplaneRemoving the Scsi Backplane Installing the Scsi BackplaneRemoving the Front Panel Board Installing the Front Panel BoardFront Panel Board Power Supply Output Voltages Power Supply SpecificationsInput Voltages Output VoltagesEnvironmental Specifications Environmental SpecificationsWide/Fast Scsi 16-Bit Connector Pinout Scsi Hot-swap Backplane ConnectorsUltra2/LVD Scsi 16-Bit Connector Wide/Fast SCA2 Scsi 16-Bit Connector Pinout Ultra2/LVD SCA2 Scsi 16-Bit ConnectorsBackplane Fan Connector Power ConnectorsPower Connector Pinout Backplane Fan Connector PinoutFront Panel Connector Pinout Front Panel Cable ConnectorRegulatory Compliance Safety ComplianceEMC Compliance Regulatory Compliance Markings Electromagnetic Compatibility Notice USAFCC Declaration of Conformity Electromagnetic Compatibility Notices InternationalVarning Installation Safety InstructionsBe UL Listed Use Only for Intended ApplicationsEquipment Log Equipment Log and WorksheetsEquipment Log Worksheet, Calculating DC Power Usage Calculating Power UsagePower Usage Worksheet Current UsageWorksheet, Total Combined Power Used by the System Page Astor II Chassis Subassembly Product Guide Page Avertissement Français Avertissement Français suite Warnung Deutsch Warnung Deutsch Fortsetzung Avvertenza Italiano Avvertenza Italiano continua Advertencias Español Advertencias Españolcontinúa Astor II Chassis Subassembly Product Guide Extent of Limited Warranty WarrantyLimitations of Liability Warranty Limitations and ExclusionsTelephone Support How to Obtain Warranty ServiceReturning a Defective Product