Intel II manual Installation Safety Instructions, Varning

Page 55

Installation Safety Instructions

CAUTION

Integration of this assembly shall be done only by technically qualified personnel.

Follow these guidelines to meet and maintain safety and product regulatory requirements when integrating this Astor II chassis subassembly.

Read and adhere to all of these instructions and the instructions supplied with this assembly. If you do not follow these instructions, the UL listing will be void, and the product will most likely be noncompliant with other regional product laws and regulations.

The following warning is provided on the server board configuration label, which is provided with the Intel server board boxed product. There is insufficient space on the server board to place this label. Therefore, the label must be placed permanently on the inside of the chassis, as close to the battery as possible.

WARNING

Danger of explosion if battery is incorrectly replaced. Replace with only the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

ADVARSEL!

Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.

ADVARSEL!

Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

Regulatory Information

55

Image 55
Contents Intel Astor II Server Chassis Subassembly Product Guide FCC Declaration of Conformity Contents Regulatory Information Technical ReferenceEquipment Log and Worksheets Figures WarrantyTables Feature Summary Kit ContentsFront Controls and Indicators Chassis Front Controls and IndicatorsBack I/O Ports and Features Chassis Back I/O Ports and FeaturesChassis Side View Chassis Side ViewHot-swap Bay PeripheralsExternal Bay for 5.25-inch Removable Media Devices Internal Bay for 3.5-inch IDE Hard DrivesChecking the Power Cord Power SupplySystem Cooling Mechanical Locks System SecurityMonitoring Intel Astor II Server Chassis Subassembly Product Guide Tools and Supplies Needed Safety Before You Remove the Side CoverRemoving the Side Cover Removing the Side Cover Installing Chassis FeetRemoving the Hot-swap Bay Removing the Hot-swap BayDisconnect Cables and Remove Screws Removing the IDE Drive BayIDE Hard Drive Bay Rubber Bumper and Standoff Clip Placement Installing Server Board Clips and BumpersShield Installing the Server BoardInstalling the Server Board typical board shown Installing a Chassis Intrusion Switch Installing a Chassis Intrusion SwitchRemoving the Front Cover Removing the Front CoverRemoving the Diskette Drive Installing the Diskette DriveIDE Requirements Installing a Hard Drive into the IDE drive bayHard Drives Drive Cabling ConsiderationsIDE Hard Drive Removing a Hard Drive from the IDE Drive BayInstalling the IDE Drive Bay Remove Filler Panels and EMI Shields Installing a 5.25-inch Peripheral DeviceSnap-in Plastic Slide Rails Removing a 5.25-inch Peripheral Device Installing a Removable Media DeviceInstalling the Hot-swap Bay Installing the Front CoverInstalling an Add-in Board Removing an Add-in Board Installing an Add-in BoardInstalling the Side Cover Scsi Hard Disk Drives Hot-swap BayMounting a Scsi SCA2 Hard Disk Drive in a Plastic Carrier Hard Disk Drive and Plastic Carrier Installing a Scsi SCA2 Hard Disk Drive in the Hot-swap BayHot-swapping a Scsi SCA2 Hard Disk Drive Installing a Hard Disk DriveFans Fan Cable Connector PinoutRemoving the Front Fan Installing the Front Fan Installing the Front FanRemoving a Hot-swap Bay Fan Installing a Hot-swap Bay FanRemoving the Scsi Backplane Hot-swap BackplaneRemoving the Scsi Backplane Installing the Scsi BackplaneFront Panel Board Installing the Front Panel BoardRemoving the Front Panel Board Output Voltages Power Supply SpecificationsPower Supply Output Voltages Input VoltagesEnvironmental Specifications Environmental SpecificationsUltra2/LVD Scsi 16-Bit Connector Scsi Hot-swap Backplane ConnectorsWide/Fast Scsi 16-Bit Connector Pinout Wide/Fast SCA2 Scsi 16-Bit Connector Pinout Ultra2/LVD SCA2 Scsi 16-Bit ConnectorsBackplane Fan Connector Pinout Power ConnectorsBackplane Fan Connector Power Connector PinoutFront Panel Connector Pinout Front Panel Cable ConnectorRegulatory Compliance Safety ComplianceEMC Compliance Regulatory Compliance Markings Electromagnetic Compatibility Notice USAFCC Declaration of Conformity Electromagnetic Compatibility Notices InternationalVarning Installation Safety InstructionsBe UL Listed Use Only for Intended ApplicationsEquipment Log Equipment Log and WorksheetsEquipment Log Current Usage Calculating Power UsageWorksheet, Calculating DC Power Usage Power Usage WorksheetWorksheet, Total Combined Power Used by the System Page Astor II Chassis Subassembly Product Guide Page Avertissement Français Avertissement Français suite Warnung Deutsch Warnung Deutsch Fortsetzung Avvertenza Italiano Avvertenza Italiano continua Advertencias Español Advertencias Españolcontinúa Astor II Chassis Subassembly Product Guide Extent of Limited Warranty WarrantyLimitations of Liability Warranty Limitations and ExclusionsTelephone Support How to Obtain Warranty ServiceReturning a Defective Product