Intel II manual Removing the Front Panel Board, Installing the Front Panel Board

Page 44

Front Panel Board

Removing the Front Panel Board

The front panel board contains the system controls and indicators. The board is mounted on a snap on standoff and a threaded standoff inside the chassis.

1.Observe the safety and ESD precautions at the beginning of this chapter.

2.Remove the side cover.

3.Remove the hot-swap bay.

4.Remove and save the snap rivets holding the front panel board to the chassis.

5.Disconnect the data cables from the front panel.

6.￿Remove the front panel board from the system, and place it on an antistatic foam pad or a grounded workstation.

OM07098

Figure 29. Removing the Front Panel Board

Installing the Front Panel Board

1.Position the front panel board over the tabs inside the chassis.

2.Reconnect the data cables to the front panel board.

3.Insert the snap rivets from the bottom, through the tabs and the front panel.

4.Reinstall the hot-swap bay.

5.￿Reinstall the side cover.

44

Intel Astor II Server Chassis Subassembly Product Guide

Image 44
Contents Intel Astor II Server Chassis Subassembly Product Guide FCC Declaration of Conformity Contents Equipment Log and Worksheets Technical ReferenceRegulatory Information Warranty FiguresTables Kit Contents Feature SummaryChassis Front Controls and Indicators Front Controls and IndicatorsChassis Back I/O Ports and Features Back I/O Ports and FeaturesChassis Side View Chassis Side ViewPeripherals External Bay for 5.25-inch Removable Media DevicesInternal Bay for 3.5-inch IDE Hard Drives Hot-swap BaySystem Cooling Power SupplyChecking the Power Cord Monitoring System SecurityMechanical Locks Intel Astor II Server Chassis Subassembly Product Guide Safety Before You Remove the Side Cover Tools and Supplies NeededRemoving the Side Cover Installing Chassis Feet Removing the Side CoverRemoving the Hot-swap Bay Removing the Hot-swap BayRemoving the IDE Drive Bay Disconnect Cables and Remove ScrewsIDE Hard Drive Bay Installing Server Board Clips and Bumpers Rubber Bumper and Standoff Clip PlacementInstalling the Server Board ShieldInstalling the Server Board typical board shown Installing a Chassis Intrusion Switch Installing a Chassis Intrusion SwitchRemoving the Front Cover Removing the Front CoverInstalling the Diskette Drive Removing the Diskette DriveInstalling a Hard Drive into the IDE drive bay Hard DrivesDrive Cabling Considerations IDE RequirementsRemoving a Hard Drive from the IDE Drive Bay IDE Hard DriveInstalling the IDE Drive Bay Installing a 5.25-inch Peripheral Device Remove Filler Panels and EMI ShieldsSnap-in Plastic Slide Rails Installing a Removable Media Device Removing a 5.25-inch Peripheral DeviceInstalling an Add-in Board Installing the Front CoverInstalling the Hot-swap Bay Installing an Add-in Board Removing an Add-in BoardInstalling the Side Cover Mounting a Scsi SCA2 Hard Disk Drive in a Plastic Carrier Hot-swap BayScsi Hard Disk Drives Installing a Scsi SCA2 Hard Disk Drive in the Hot-swap Bay Hard Disk Drive and Plastic CarrierInstalling a Hard Disk Drive Hot-swapping a Scsi SCA2 Hard Disk DriveRemoving the Front Fan Fan Cable Connector PinoutFans Installing the Front Fan Installing the Front FanInstalling a Hot-swap Bay Fan Removing a Hot-swap Bay FanHot-swap Backplane Removing the Scsi BackplaneInstalling the Scsi Backplane Removing the Scsi BackplaneRemoving the Front Panel Board Installing the Front Panel BoardFront Panel Board Power Supply Specifications Power Supply Output VoltagesInput Voltages Output VoltagesEnvironmental Specifications Environmental SpecificationsWide/Fast Scsi 16-Bit Connector Pinout Scsi Hot-swap Backplane ConnectorsUltra2/LVD Scsi 16-Bit Connector Ultra2/LVD SCA2 Scsi 16-Bit Connectors Wide/Fast SCA2 Scsi 16-Bit Connector PinoutPower Connectors Backplane Fan ConnectorPower Connector Pinout Backplane Fan Connector PinoutFront Panel Cable Connector Front Panel Connector PinoutSafety Compliance Regulatory ComplianceEMC Compliance Electromagnetic Compatibility Notice USA Regulatory Compliance MarkingsElectromagnetic Compatibility Notices International FCC Declaration of ConformityInstallation Safety Instructions VarningUse Only for Intended Applications Be UL ListedEquipment Log and Worksheets Equipment LogEquipment Log Calculating Power Usage Worksheet, Calculating DC Power UsagePower Usage Worksheet Current UsageWorksheet, Total Combined Power Used by the System Page Astor II Chassis Subassembly Product Guide Page Avertissement Français Avertissement Français suite Warnung Deutsch Warnung Deutsch Fortsetzung Avvertenza Italiano Avvertenza Italiano continua Advertencias Español Advertencias Españolcontinúa Astor II Chassis Subassembly Product Guide Warranty Extent of Limited WarrantyWarranty Limitations and Exclusions Limitations of LiabilityHow to Obtain Warranty Service Telephone SupportReturning a Defective Product