Intel II manual Electromagnetic Compatibility Notices International, FCC Declaration of Conformity

Page 54

NOTE

If a Class A device is installed within this system, then the system is to be considered a Class A system. In this configuration, operation of this equipment in a residential area is likely to cause harmful interference.

FCC Declaration of Conformity

Product Type: AST2

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Intel Corporation

5200 N.E. Elam Young Parkway

Hillsboro, OR 97124-6497

Phone: 1-800-628-8686

Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003 édictée par le Ministre Canadian des Communications.

(English translation of the notice above) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the interference causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Canadian Department of Communications.

Electromagnetic Compatibility Notices (International)

(English translation of the notice above) This is a Class B product based on the standard of the Voluntary Control Council For Interference (VCCI) from Information Technology Equipment. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

When used near a radio or TV receiver, it may become the cause of radio interference.

Read the instructions for correct handling.

This equipment has been tested for radio frequency emissions and has been verified to meet CISPR 22 Class B.

54

Intel Astor II Server Chassis Subassembly Product Guide

Image 54
Contents Intel Astor II Server Chassis Subassembly Product Guide FCC Declaration of Conformity Contents Technical Reference Regulatory InformationEquipment Log and Worksheets Warranty FiguresTables Kit Contents Feature SummaryChassis Front Controls and Indicators Front Controls and IndicatorsChassis Back I/O Ports and Features Back I/O Ports and FeaturesChassis Side View Chassis Side ViewInternal Bay for 3.5-inch IDE Hard Drives PeripheralsExternal Bay for 5.25-inch Removable Media Devices Hot-swap BayPower Supply Checking the Power CordSystem Cooling System Security Mechanical LocksMonitoring Intel Astor II Server Chassis Subassembly Product Guide Safety Before You Remove the Side Cover Tools and Supplies NeededRemoving the Side Cover Installing Chassis Feet Removing the Side CoverRemoving the Hot-swap Bay Removing the Hot-swap BayRemoving the IDE Drive Bay Disconnect Cables and Remove ScrewsIDE Hard Drive Bay Installing Server Board Clips and Bumpers Rubber Bumper and Standoff Clip PlacementInstalling the Server Board ShieldInstalling the Server Board typical board shown Installing a Chassis Intrusion Switch Installing a Chassis Intrusion SwitchRemoving the Front Cover Removing the Front CoverInstalling the Diskette Drive Removing the Diskette DriveDrive Cabling Considerations Installing a Hard Drive into the IDE drive bayHard Drives IDE RequirementsRemoving a Hard Drive from the IDE Drive Bay IDE Hard DriveInstalling the IDE Drive Bay Installing a 5.25-inch Peripheral Device Remove Filler Panels and EMI ShieldsSnap-in Plastic Slide Rails Installing a Removable Media Device Removing a 5.25-inch Peripheral DeviceInstalling the Front Cover Installing the Hot-swap BayInstalling an Add-in Board Installing an Add-in Board Removing an Add-in BoardInstalling the Side Cover Hot-swap Bay Scsi Hard Disk DrivesMounting a Scsi SCA2 Hard Disk Drive in a Plastic Carrier Installing a Scsi SCA2 Hard Disk Drive in the Hot-swap Bay Hard Disk Drive and Plastic CarrierInstalling a Hard Disk Drive Hot-swapping a Scsi SCA2 Hard Disk DriveFan Cable Connector Pinout FansRemoving the Front Fan Installing the Front Fan Installing the Front FanInstalling a Hot-swap Bay Fan Removing a Hot-swap Bay FanHot-swap Backplane Removing the Scsi BackplaneInstalling the Scsi Backplane Removing the Scsi BackplaneInstalling the Front Panel Board Front Panel BoardRemoving the Front Panel Board Input Voltages Power Supply SpecificationsPower Supply Output Voltages Output VoltagesEnvironmental Specifications Environmental SpecificationsScsi Hot-swap Backplane Connectors Ultra2/LVD Scsi 16-Bit ConnectorWide/Fast Scsi 16-Bit Connector Pinout Ultra2/LVD SCA2 Scsi 16-Bit Connectors Wide/Fast SCA2 Scsi 16-Bit Connector PinoutPower Connector Pinout Power ConnectorsBackplane Fan Connector Backplane Fan Connector PinoutFront Panel Cable Connector Front Panel Connector PinoutSafety Compliance Regulatory ComplianceEMC Compliance Electromagnetic Compatibility Notice USA Regulatory Compliance MarkingsElectromagnetic Compatibility Notices International FCC Declaration of ConformityInstallation Safety Instructions VarningUse Only for Intended Applications Be UL ListedEquipment Log and Worksheets Equipment LogEquipment Log Power Usage Worksheet Calculating Power UsageWorksheet, Calculating DC Power Usage Current UsageWorksheet, Total Combined Power Used by the System Page Astor II Chassis Subassembly Product Guide Page Avertissement Français Avertissement Français suite Warnung Deutsch Warnung Deutsch Fortsetzung Avvertenza Italiano Avvertenza Italiano continua Advertencias Español Advertencias Españolcontinúa Astor II Chassis Subassembly Product Guide Warranty Extent of Limited WarrantyWarranty Limitations and Exclusions Limitations of LiabilityHow to Obtain Warranty Service Telephone SupportReturning a Defective Product