Furuno FR-2115-B installation manual Processor unit, inside view

Page 55

1.Open the processor unit.

2.Follow a) and b) of "how to access rear-left fixing hole" on page 7 to remove the PTU Board cover.

3.Unplug all connectors from the PTU Board.

4.Loosen the screws fixing the PTU Board, and then remove the PTU Board.

5.Fasten new PTU Board with screws removed in step 4.

6.Plug in six connectors to their proper locations on the PTU Board. Do not connect J101.

7.Loosen four screws fixing the AC filter.

8.Fasten new filter.

9.Connect cable from filter to J101 on the PTU Board.

10.Fasten the PTU board cover.

11.Connect power cable from ship's mains.

12.Close the processor unit.

 

 

PTU Board (behind shield cover)

 

Screw

 

Knob

*

Power cable

 

 

(M3X8, 5 pcs.)

*

 

*

leads

Slide forward

 

 

 

 

 

 

 

*

 

*

Unfasten

 

 

 

 

screws.

Filter

(Shown:

AC type)

ScrewJ446(M4X8, 2 pcs.)

J466

J462

Figure 4-15 Processor unit, inside view

4-16

Image 55
Contents Marine Radar FR-2115-B/FR-2125-B B . N o . I M E 3 4 8 3 0 H Radio Frequency Radiation Hazard Safety InstructionsDo not open the equipment Equipment Lists Standard supply System without monitor Optional equipment Data Sentences System ConfigurationMounting Assembling the antenna unit Fastening the radiator to the radiator bracket Fastening the antenna unit to the mounting platform How to mount the antenna unit Processor Unit Mounting the processor unit Processor unit, inside view Monitor Mounting the monitor Control Unit Mounting the antenna chassis Antenna UnitAntenna unit, front view, cover removed Correct seating of waterproofing gasket 2C-2V Fabricating signal cable S03-75Processor Unit Fabricating the AC power cableCVV-S 8X2C Fabricating the DC power cable CVV-S 8X2C, optionANT Leading in cables to the processor unitMonitor Connect the monitor cable inside the monitor as below Connection of monitor cable inside the monitorControl Unit Power Connectors on the INT Board How to attach NH connector AC Power Specification of Processor UnitRestoring default settings Tuning InitializationAccessing Menus for Initialization and Adjustment Adjusting Video Signal LevelPicture appears Deviated counterclockwise Heading AlignmentSuppressing Main Bang Adjusting Sweep TimingMagnetron heater voltage rating Confirming Magnetron Heater VoltagePress Radar Menu 0 0 0 Initial Setting MenusInitial SETTING1 menu Initial SETTING3 menu Gyro Converter GC-8 Installation and connection of the Gyro Converter BoardINT Board Gyro Converter Board J446 4P J7 5P J465 6P J1 14P DIP switch, jumper wire settings Connection of external power supplyRotor Voltage between R1 & R2 Stator Voltage between S1 & S2 JP1 JP2 JP3 JP4 JP5 SW1 Setting the heading readout on the radar displayARP Board ARP-26 ARP Board 18P9002B ARP board adjustmentFinal check of ARP board RP Board RP-2610 Processor unit, inside view 11 Processor unit, front view 12 Processor, front and top views Necessary parts PM-30 and OP03-150 Code no Performance Monitor PM-30Alarm Kit J474 Arpa CPA/TCPA AC-DC Conversion Kit15 Processor unit, inside view Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page