Multiquip GB114BS/BP Installing a NEW Lamp, Replacing the Balloon, Reconnect the power cables

Page 22

MAINTENANCE

3.Push down and hold the lamp holder (spring loaded) away from the lamp (Figure 21). Unscrew the lamp (turn counterclockwise) from the lamp socket.

LAMP

SOCKET

LAMP

HOLDER

TO REMOVE LAMP

PUSH TURN COUNTER-

DOWN CLOCKWISE

Figure 21. Removing the Lamp

INSTALLING A NEW LAMP

1.When installing a new lamp (Figure 22) use only MQ recommended type lamp. See parts section of this manual. Failure to use correct type lamp could adversely affect lighting capability and may cause damage to the equipment.

2.Push down and hold the lamp holder (spring loaded) away from the lamp. Screw the lamp (turn clockwise) into the lamp socket. Gently place the lamp holder fi rmly over the top of the lamp. This will prevent the lamp from touching the lamp guard or pipe frame.

LAMP

SOCKET

LAMP

HOLDER

(SPRING-LOADED)

TO INSTALL LAMP

TURN CLOCKWISE

PLACE

LAMP HOLDER

FIRMLY ONTO

LAMP TOP

Figure 22. Installing the Lamp

R E - I N S TA L L I N G T H E L A M P / BA L L O O N ASSEMBLY

1.Reinstall the lamp guard (Figure 23). Be careful not to install the lamp guard in the wrong direction.

BALLOON

PIPE FRAME

SNAP LAMP

GUARD INTO

PIPE FRAME

Figure 23. Installing the Lamp Guard

2.Zip up the zipper at the bottom (Figure 19) of the balloon and pull down the balloon envelope to cover the lamp

3.Place the lamp/balloon assembly back onto the mast.

4.Tighten the T-Handle Bolt Lock to secure the lamp to the mast.

5.Reinstall the protective cover over the balloon/lamp assembly. Be sure to fold the velcro tabs.

6.Reconnect the power cables.

REPLACING THE BALLOON

1.Follow the procedures as outlined in the "Removing the Balloon Lamp" assembly section.

2.Unzip the zipper at the bottom and top of the balloon. Slide the balloon over the top of the lamp guard as shown in Figure 24.

LAMP

GUARD BALLOON

Figure 24. Removing the Balloon

3.Slide the new balloon over the top of the lamp guard as shown in Figure 25. Zip up the zipper at the bottom and top of the balloon.

LAMP

GUARD BALLOON

Figure 25. Removing the Balloon

PAGE 22 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09)

Image 22
Contents Model GB114BS/BP This Manual Must Accompany the Equipment AT ALL TimesTable of Contents MQ Globug Lighting SystemParts Ordering Procedures Ordering parts has never been easierSafety Symbols Safety InformationSafety Messages General SafetyBalloon Safety Lighting System SafetyLamp Safety  Never attempt service on a running machineElectrical Safety Generator Safety Always make sure the area above Transporting Safety Loading and UnloadingSpecifications Dimensions GB114BS DimensionsDimensions GB114BP Dimensions GB114BPFootcandle Plot CoverageGeneral Information Page Components Major ComponentsComponents Setup Pole SetupConnecting Power Cable Removing the Protective CoveringOperation Applying PowerRaising the Extension Pole OPERATION/SHUTDOWN Place the ON/OFF switch on the ballast in the on positionShutdown Lowering the Extension Pole Removing Lamp AssemblyStorage Fully zip protective cover and fold velcro tab in placeMaintenance Handle KnobReconnect the power cables Installing a NEW LampI N S TA L L I N G T H E L a M P / BA L L O O N Assembly Replacing the BalloonFilter Replacement Balloon/Lamp PlacementMaintenance Check Points Plug Damaged? Replace Lamp Switch Connector Cable disconnected or loose?Broken? Replace Power Cable Defective or worn cable? Lamp Base Lamp base loose?Troubleshooting Lamp Wiring Diagram BallastVoltage Measurement Lamp Cable NO- Load Place the ballast ON/OFF switch in the OFF positionVoltage Measurements Voltage Measurement Lamp Socket NO- LoadVoltage Measurements Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts GB114BP/BS Globug Lighting SystemNameplate and Decals Electrical Shock HazardDCL416 DCL1001DCL1002 DCL417Ballast ASSEMBLY. S/N G30001 A300033800 A000017700A100010202 A200016900Ballast ASSEMBLY. S/N G30002 & Above A200020904 A000017702A100015401 A400079400FAN BLOWER/LAMP Base Assembly A000017601 A000017600G30001 A300033600BALLOON/LAMP Guard Assembly 2204220130 A1000285053A# A300060202 1800001000Offset Pole Assembly A200018303 A000018200A200019103 0013512045Terms and Conditions of Sale Parts Freight PolicyPage HERE’S HOW to GET Help