Multiquip GB114BS/BP manual Storage, Lowering the Extension Pole, Removing Lamp Assembly, Damaged

Page 20

STORAGE

NOTICE

Allow a sufficient amount of time (15-20 minutes) for the lamp to cool down .The possibility exists of the balloon getting burned (touching the lamp).

LOWERING THE EXTENSION POLE

1.Using the supplied 19 mm wrench, loosen extension clamp bolt (Figure 6-Q).

2.Carefully pull down on the adjustable extension pole (Figure 6-L) and lower lamp assembly.

3.Remove wingnut (Figure 6-D) from offset pole (Figure 6B) and insert wrench into wrench holder. Reinsert wingnut and tighten.

REMOVING LAMP ASSEMBLY

1.Disconnect balloon power cable (Figure 13) from the lamp power cable. Place lamp power cable in a safe place where it will not get damage or lost..

BALLOON

 

POWER

LAMP

CABLE

ASSEMBLY

 

LAMP

POWER

CABLE

Figure 13. Disconnecting Power Cables

2.Remove both S-type hooks (Figure 9) on the lamp power cable from the cable support holes on the offset pole.

3.Unzip the zipper on the protective cover (Figure 14), and pull down cover over balloon/lamp assembly.

ZIPPER

PROTECTIVE

COVER

Figure 14. Unzipping the Protective Cover

4. Fully zip protective cover and fold velcro tab in place.

PROTECTIVE

COVER

VELCRO

TAB

Figure 15. Zipping the Protective Cover

5.Loosen T-handle bolt (Figure 6-O) by turning counterclockwise and remove lamp assembly (Figure 6-N) from offset pole.

6.Store lamp assembly enclosed within its protective cover (Figure 16) in a safe location where it will not be

damaged.

COVER/LAMP

CARRYING

CASE

Figure 16. Storing Lamp Assembly

PAGE 20 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09)

Image 20
Contents Model GB114BS/BP This Manual Must Accompany the Equipment AT ALL TimesTable of Contents MQ Globug Lighting SystemParts Ordering Procedures Ordering parts has never been easierSafety Information Safety MessagesSafety Symbols General SafetyLighting System Safety Lamp SafetyBalloon Safety  Never attempt service on a running machine Always make sure the area above Generator SafetyElectrical Safety Transporting Safety Loading and UnloadingSpecifications Dimensions GB114BS DimensionsDimensions GB114BP Dimensions GB114BPFootcandle Plot CoverageGeneral Information Page Components Major ComponentsComponents Setup Pole SetupConnecting Power Cable Removing the Protective CoveringRaising the Extension Pole Applying PowerOperation Shutdown Place the ON/OFF switch on the ballast in the on positionOPERATION/SHUTDOWN Removing Lamp Assembly StorageLowering the Extension Pole Fully zip protective cover and fold velcro tab in placeMaintenance Handle KnobInstalling a NEW Lamp I N S TA L L I N G T H E L a M P / BA L L O O N AssemblyReconnect the power cables Replacing the BalloonFilter Replacement Balloon/Lamp PlacementMaintenance Check Points Connector Cable disconnected or loose? Broken? Replace Power Cable Defective or worn cable?Plug Damaged? Replace Lamp Switch Lamp Base Lamp base loose?Troubleshooting Lamp Wiring Diagram BallastPlace the ballast ON/OFF switch in the OFF position Voltage MeasurementsVoltage Measurement Lamp Cable NO- Load Voltage Measurement Lamp Socket NO- LoadVoltage Measurements Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts GB114BP/BS Globug Lighting SystemNameplate and Decals Electrical Shock HazardDCL1001 DCL1002DCL416 DCL417Ballast ASSEMBLY. S/N G30001 A000017700 A100010202A300033800 A200016900Ballast ASSEMBLY. S/N G30002 & Above A000017702 A100015401A200020904 A400079400FAN BLOWER/LAMP Base Assembly A000017600 G30001A000017601 A300033600BALLOON/LAMP Guard Assembly A100028505 3A# A3000602022204220130 1800001000Offset Pole Assembly A000018200 A200019103A200018303 0013512045Terms and Conditions of Sale Parts Freight PolicyPage HERE’S HOW to GET Help