Multiquip GB114BS/BP manual Filter Replacement, Balloon/Lamp Placement

Page 23

MAINTENANCE

CAUTION

DO NOT replace ﬁ lter immediately, allow a sufﬁ cient amount of time for the lamp assembly to cool down before changing ﬁ lter

FILTER REPLACEMENT

1.Remove the balloon as described in the "Removing the Lamp/Balloon" section.

2.Disconnect the lamp power cable (Figure 5).

3.Rotate the balloon/lamp base assembly so that the ﬁ lter is facing upwards. See Figure 26.

BALLOON/LAMP

Figure 26. Balloon/Lamp Placement

4.Turn the three locking tabs (Figure 27) inward to release the plate. Remove plate and ﬁ lter.

PLATE

FILTER

TURN

OUTWARD

TO RELEASE

LOCKING

TAB

Figure 27. Filter Removal

5.Install a new ﬁ lter over the brace as shown in Figure 28. Be sure to align the cut of the ﬁ lter over the brace.

BRACE

FILTER

CUT

Figure 28. Filter Placement

CAUTION

When placing the ﬁ lter element, always align the cut of the ﬁ lter on top of the brace. This will keep the ﬁ lter from being dislodged and getting damaged.

6.Turn the three retaining tabs (Figure 29) outward so that they touch the lamp base.

PLATE

FILTER

TURN

INWARD

TO LOCK

LOCKING

TAB

Figure 29. Filter/Plate Install

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 23

Image 23

Contents This Manual Must Accompany the Equipment AT ALL Times Model GB114BS/BPMQ Globug Lighting System Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresGeneral Safety Safety InformationSafety Messages Safety Symbols Never attempt service on a running machine Lighting System SafetyLamp Safety Balloon Safety Always make sure the area above Generator SafetyElectrical Safety Loading and Unloading Transporting SafetySpecifications Dimensions Dimensions GB114BSDimensions GB114BP Dimensions GB114BPCoverage Footcandle PlotGeneral Information Page Major Components ComponentsComponents Pole Setup SetupRemoving the Protective Covering Connecting Power CableRaising the Extension Pole Applying PowerOperation Shutdown Place the ON/OFF switch on the ballast in the on positionOPERATION/SHUTDOWN Fully zip protective cover and fold velcro tab in place Removing Lamp AssemblyStorage Lowering the Extension PoleHandle Knob MaintenanceReplacing the Balloon Installing a NEW LampI N S TA L L I N G T H E L a M P / BA L L O O N Assembly Reconnect the power cablesBalloon/Lamp Placement Filter ReplacementMaintenance Check Points Lamp Base Lamp base loose? Connector Cable disconnected or loose?Broken? Replace Power Cable Defective or worn cable? Plug Damaged? Replace Lamp SwitchTroubleshooting Lamp Ballast Wiring DiagramVoltage Measurement Lamp Socket NO- Load Place the ballast ON/OFF switch in the OFF positionVoltage Measurements Voltage Measurement Lamp Cable NO- LoadVoltage Measurements Explanation of Code in Remarks Column Sample Parts ListGB114BP/BS Globug Lighting System Suggested Spare PartsElectrical Shock Hazard Nameplate and DecalsDCL417 DCL1001DCL1002 DCL416Ballast ASSEMBLY. S/N G30001 A200016900 A000017700A100010202 A300033800Ballast ASSEMBLY. S/N G30002 & Above A400079400 A000017702A100015401 A200020904FAN BLOWER/LAMP Base Assembly A300033600 A000017600G30001 A000017601BALLOON/LAMP Guard Assembly 1800001000 A1000285053A# A300060202 2204220130Offset Pole Assembly 0013512045 A000018200A200019103 A200018303Freight Policy Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help