Multiquip GB114BS/BP manual Generator Safety, Electrical Safety,  Always make sure the area above

Page 6

SAFETY INFORMATION

GENERATOR SAFETY

If using a generator to power lighting system, refer to applicable generator manual safety information section.

ELECTRICAL SAFETY

DANGER

Lighting system is equipped with a ground pin on the power plug. For your protection, ALWAYS complete the grounding path. NEVER insert the AC power plug into a 2-prong receptacle to operate lighting system.

When applying power to the lighting system, ALWAYS connect the AC power plug to a 3-prong receptacle that is grounded. The possibility exists of electrical shock, electrocution and even death if the lighting system is not grounded.

NEVER operate lighting system or handle any electrical equipment while standing in water, while barefoot, while hands are wet or in the rain. A dangerous electrical shock could occur, causing severe bodily harm or even death.

ALWAYS make sure the area above

the lighting system is open and clear of overhead power lines and other obstructions. Contact with overhead power lines or other obstructions could result in equipment damage, electrical shock, electrocution and even death.

Power Cord/Cable Safety

DANGER

NEVER let power cords or cables lay in water.

NEVER use damaged or worn cables or cords. Inspect for cuts in the insulation

NEVER grab or touch a live power cord or cable with wet hands. The possibility exists of electrical shock, electrocution or death.

Make sure power cables are securely connected. Incorrect connections may cause electrical shock and damage to the lighting system.

NOTICE

ALWAYS make certain that proper power or extension cord has been selected for the job. See Cable Selection Chart in this manual.

PAGE 6 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09)

Image 6
Contents Model GB114BS/BP This Manual Must Accompany the Equipment AT ALL TimesTable of Contents MQ Globug Lighting SystemParts Ordering Procedures Ordering parts has never been easierSafety Symbols Safety InformationSafety Messages General SafetyBalloon Safety Lighting System SafetyLamp Safety  Never attempt service on a running machineGenerator Safety Electrical Safety Always make sure the area above Transporting Safety Loading and UnloadingSpecifications Dimensions GB114BS DimensionsDimensions GB114BP Dimensions GB114BPFootcandle Plot CoverageGeneral Information Page Components Major ComponentsComponents Setup Pole SetupConnecting Power Cable Removing the Protective CoveringApplying Power OperationRaising the Extension Pole Place the ON/OFF switch on the ballast in the on position OPERATION/SHUTDOWNShutdown Lowering the Extension Pole Removing Lamp AssemblyStorage Fully zip protective cover and fold velcro tab in placeMaintenance Handle KnobReconnect the power cables Installing a NEW LampI N S TA L L I N G T H E L a M P / BA L L O O N Assembly Replacing the BalloonFilter Replacement Balloon/Lamp PlacementMaintenance Check Points Plug Damaged? Replace Lamp Switch Connector Cable disconnected or loose?Broken? Replace Power Cable Defective or worn cable? Lamp Base Lamp base loose?Troubleshooting Lamp Wiring Diagram BallastVoltage Measurement Lamp Cable NO- Load Place the ballast ON/OFF switch in the OFF positionVoltage Measurements Voltage Measurement Lamp Socket NO- LoadVoltage Measurements Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts GB114BP/BS Globug Lighting SystemNameplate and Decals Electrical Shock HazardDCL416 DCL1001DCL1002 DCL417Ballast ASSEMBLY. S/N G30001 A300033800 A000017700A100010202 A200016900Ballast ASSEMBLY. S/N G30002 & Above A200020904 A000017702A100015401 A400079400FAN BLOWER/LAMP Base Assembly A000017601 A000017600G30001 A300033600BALLOON/LAMP Guard Assembly 2204220130 A1000285053A# A300060202 1800001000Offset Pole Assembly A200018303 A000018200A200019103 0013512045Terms and Conditions of Sale Parts Freight PolicyPage HERE’S HOW to GET Help