Multiquip GB114BS/BP manual Safety Information, Safety Messages, Safety Symbols, General Safety

Page 4

SAFETY INFORMATION

Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment.

Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you about potential hazards that could injure you or others.The safety messages specifi cally address the level of exposure to the operator and are preceded by one of four words: DANGER, WARNING, CAUTION or NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided, COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.

GENERAL SAFETY

CAUTION

NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations.

NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication.

NEVER operate this equipment under the infl uence of drugs or alcohol.

NOTICE

This equipment should only be operated by trained and qualifi ed personnel 18 years of age and older.

Whenever necessary, replace nameplate, operation and safety decals when they become diffi cult read.

Manufacturer does not assume responsibility for any accident due to equipment modifi cations. Unauthorized equipment modifi cation will void all warranties.

NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

ALWAYS know the location of the nearest

fire extinguisher.

ALWAYS know the location of the nearest

first aid kit.

ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency.

PAGE 4 — GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09)

Image 4
Contents Model GB114BS/BP This Manual Must Accompany the Equipment AT ALL TimesTable of Contents MQ Globug Lighting SystemParts Ordering Procedures Ordering parts has never been easierSafety Information Safety MessagesSafety Symbols General SafetyLighting System Safety Lamp SafetyBalloon Safety  Never attempt service on a running machineElectrical Safety Generator Safety Always make sure the area above Transporting Safety Loading and UnloadingSpecifications Dimensions GB114BS DimensionsDimensions GB114BP Dimensions GB114BPFootcandle Plot CoverageGeneral Information Page Components Major ComponentsComponents Setup Pole SetupConnecting Power Cable Removing the Protective CoveringOperation Applying PowerRaising the Extension Pole OPERATION/SHUTDOWN Place the ON/OFF switch on the ballast in the on positionShutdown Removing Lamp Assembly StorageLowering the Extension Pole Fully zip protective cover and fold velcro tab in placeMaintenance Handle KnobInstalling a NEW Lamp I N S TA L L I N G T H E L a M P / BA L L O O N AssemblyReconnect the power cables Replacing the BalloonFilter Replacement Balloon/Lamp PlacementMaintenance Check Points Connector Cable disconnected or loose? Broken? Replace Power Cable Defective or worn cable?Plug Damaged? Replace Lamp Switch Lamp Base Lamp base loose?Troubleshooting Lamp Wiring Diagram BallastPlace the ballast ON/OFF switch in the OFF position Voltage MeasurementsVoltage Measurement Lamp Cable NO- Load Voltage Measurement Lamp Socket NO- LoadVoltage Measurements Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts GB114BP/BS Globug Lighting SystemNameplate and Decals Electrical Shock HazardDCL1001 DCL1002DCL416 DCL417Ballast ASSEMBLY. S/N G30001 A000017700 A100010202A300033800 A200016900Ballast ASSEMBLY. S/N G30002 & Above A000017702 A100015401A200020904 A400079400FAN BLOWER/LAMP Base Assembly A000017600 G30001A000017601 A300033600BALLOON/LAMP Guard Assembly A100028505 3A# A3000602022204220130 1800001000Offset Pole Assembly A000018200 A200019103A200018303 0013512045Terms and Conditions of Sale Parts Freight PolicyPage HERE’S HOW to GET Help