Multiquip GB114BS/BP manual Removing the Protective Covering, Connecting Power Cable

Page 17

SETUP

REMOVING THE PROTECTIVE COVERING

1.Expose the balloon by pulling down on the velcro tab and unzip the protective cover as shown in Figure 7.

	STEP 1	PROTECTIVE
	STEP 1	COVER
	UNZIP	COVER
	UNZIP
	PROTECTIVE
	COVER
	BALOON

	STEP 2
	FOLD PROTECTIVE	VELCRO
	COVER INTO ITSELF	VELCRO
	COVER INTO ITSELF	TAB
		TAB

BALLOON

FULLY

EXPOSED

CONNECTING POWER CABLE

1.Connect 16.4 ft. (5 meters) lamp power cable (Figure 8) to the balloon power cable.

	BALLOON
	POWER	LAMP
	CABLE	LAMP
	CABLE	ASSEMBLY
		ASSEMBLY

BALLAST

LAMP

POWER

CABLE

Figure 8. Connecting Lamp Power Cable

		2. Attach both S-type hooks (Figure 9) on the lamp power
		cable into the cable support holes on the offset pole.
		OFFSET
	Figure 7. Folding Protective Cover	POLE
	Figure 7. Folding Protective Cover	LAMP
		LAMP
		POWER
		CABLE

S-TYPE

HOOK

Figure 9. Attachment of S-Hooks

GB114BS/BP GLOBUG LIGHTING SYSTEM • OPERATION AND PARTS MANUAL — REV. #3 (01/06/09) — PAGE 17

Image 17

Contents This Manual Must Accompany the Equipment AT ALL Times Model GB114BS/BPMQ Globug Lighting System Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresSafety Messages Safety InformationSafety Symbols General SafetyLamp Safety Lighting System SafetyBalloon Safety  Never attempt service on a running machine Always make sure the area above Generator SafetyElectrical Safety Loading and Unloading Transporting SafetySpecifications Dimensions Dimensions GB114BSDimensions GB114BP Dimensions GB114BPCoverage Footcandle PlotGeneral Information Page Major Components ComponentsComponents Pole Setup SetupRemoving the Protective Covering Connecting Power CableRaising the Extension Pole Applying PowerOperation Shutdown Place the ON/OFF switch on the ballast in the on positionOPERATION/SHUTDOWN Storage Removing Lamp AssemblyLowering the Extension Pole Fully zip protective cover and fold velcro tab in placeHandle Knob MaintenanceI N S TA L L I N G T H E L a M P / BA L L O O N Assembly Installing a NEW LampReconnect the power cables Replacing the BalloonBalloon/Lamp Placement Filter ReplacementMaintenance Check Points Broken? Replace Power Cable Defective or worn cable? Connector Cable disconnected or loose?Plug Damaged? Replace Lamp Switch Lamp Base Lamp base loose?Troubleshooting Lamp Ballast Wiring DiagramVoltage Measurements Place the ballast ON/OFF switch in the OFF positionVoltage Measurement Lamp Cable NO- Load Voltage Measurement Lamp Socket NO- LoadVoltage Measurements Explanation of Code in Remarks Column Sample Parts ListGB114BP/BS Globug Lighting System Suggested Spare PartsElectrical Shock Hazard Nameplate and DecalsDCL1002 DCL1001DCL416 DCL417Ballast ASSEMBLY. S/N G30001 A100010202 A000017700A300033800 A200016900Ballast ASSEMBLY. S/N G30002 & Above A100015401 A000017702A200020904 A400079400FAN BLOWER/LAMP Base Assembly G30001 A000017600A000017601 A300033600BALLOON/LAMP Guard Assembly 3A# A300060202 A1000285052204220130 1800001000Offset Pole Assembly A200019103 A000018200A200018303 0013512045Freight Policy Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help