Furuno FSV-24S installation manual Monitor unit, Mounting procedure

Page 17

Mounting procedure

1.Unfasten two bolts from the bottom of the front side of the processor unit, and pull the unit toward you to separate the unit from the mounting base.

2.Fasten six bolts (M6x20, supplied as installation material) to install the mounting base.

3.Place the processor unit in front of the mounting base.

4.Push the unit forward until it touches the end of the mounting base.

5.Refasten two bolts removed at step 1 to fix the unit.

5.5

505

477

160+1

 

34

8

 

200+1 195+1

Front view

Top view

Processor unit

1.2.2Monitor unit

Mounting considerations

The monitor unit is designed for mounting on a tabletop.

Locate the monitor unit where it can be easily operated while viewing the screen and operating the control unit.

Locate the monitor unit out of direct sunlight and away from heat sources because of heat that can build up inside the cabinet.

Locate the equipment away from places subject to water splash and rain.

Be sure the mounting location is strong enough to support the weight of the unit under the continued vibration which is normally experienced on the ship. If necessary reinforce the mounting location.

The length of the monitor cable which runs between the processor unit and the monitor unit is 10 m. Keep this distance in mind when selecting a mounting location.

Leave sufficient space on the sides and rear of the unit to facilitate maintenance.

1-9

Image 17
Contents Check List Iii00080916714 Safety Instructions Projected Raising Lowering Mm stroke Max kt Standard type System ConfigurationControl Unit Black box typeStandard supply Equipment ListsSEM-21Q OptionsLocation of hull unit Mounting the Hull UnitMaintenance space, example sonar compartment Shortening the retraction tank Retraction tank Reinforcement rib 250-300 mm Remarks for installation of retraction tankInstalling hull unit on retraction tank Installation of hull unit Bow Stay Hull Unit Installing stays anti-vibration measureProcessor unit Mounting the Display UnitMonitor unit Mounting procedureMonitor unit Attaching the CRT filter Control unitFixing without KB fixing plate KB fixing plate Mounting the Transceiver Unit Mounting the Power Supply UnitGrounding the Equipment Procedure Page Mounting the Cable for Extension Kit option Attachment Kit option Using the optional attachment kit How to use the pin extractor How to Use the Crimping Tool, Pin ExtractorHow to use the crimping tool Local supply Location of ConnectorsTransceiver unit side Fabrication of monitor cable 10S2074 10 m/10S2075 30 m Monitor UnitPositioning guide pins Control cable Assembling D-SUB connector CN-A302How to connect cables to the monitor unit 1 10S1258-1 cable Processor UnitPower cable Monitor cable 10S2074 or 10S2075 Optional equipment Schematic view of cablesGyro Processor EXT-KPunit Transceiver Unit Fabrication of connector 00-8016-038-313761HV CN-B101Hull control cable 10S2078 Fabrication of power cable type DPYCY-4 TB-B101Connection Junction box Power Supply UnitCable for Extension Kit Cable clamp CKS clamp Raise/Lower Control Box Power cable fabrication Adjustment and Check Test Menu OFF Heading adjustment Heading AdjustmentSystem menu OWN Ship Mark menu Configuring Own Ship MarkTD Position Other System Menu Items Interface Setting menuSpeed & Course EXT Data Setting menuWind Others menuLanguage Adjusting the volume of audio alarm Cone Board Setting in the Processor UnitAdjustment of signal level echo sounder connected 1 CIF2/NMEA2 connector interface selection DIP Switch SettingSelecting the Net Sonde information Selecting echosounder signalTesting TX/RX independently at hull unit This page is intentionally left blank Connecting the External Interface CS-120A VH4P PP GND Ciftxdh Ciftxdc Cifrxdh Cifrxdc Shield Check List Data Sheet Data Sheet Dispaly Unit FSV-2400 User menu Color response curve sheet H 工事材料表 006-921-240-00 10CO-X-9402 006-921-250-00 10CO-X-9403 10CO-X-9412 Page 10CO-X-9406 10CO-X-9410 Furuno Electric CO .,LTD C1318-M10-C 付属品表 Page Page Page 000-144-382-00 000-155-839-10 000-157-497-10 Page Page Page Page Page Page Jan Jan Hatai Hatai Page Page Page Color Scanning Sonar Title FSV-24/24S Miyosi 制御部