Furuno CSH-24F, CSH-23F manual Safety Instructions

Page 3

SAFETY INSTRUCTIONS

WARNING

Do not open the cover unless totally familiar with electrical circuits and service manual.

High voltage exists inside the equipment, and a residual charge remains in capacitors several minutes after the power is turned off. Improper handling can result in electri- cal shock.

Turn off the power at the switchboard before beginning the installation.

Fire or electrical shock can result if the power is left on.

Do not install the equipment where it may get wet from rain or water splash.

Water in the equipment can result in fire, electrical shock or equipment damage.

Be sure no water leaks in at the trans- ducer installation site.

Water leakage can sink the vessel. Also confirm that the transducer will not loosen by ship’s vibration. The installer of the equipment is solely responsible for the proper installation of the equipment. FURUNO will assume no responsibility for any damage associated with improper installation.

WARNING

Install the specified transducer tank in accordance with the installation instructions. If a different tank is to be installed the shipyard is solely respon- sible for its installation, and it should be installed so the hull will not be damaged if the tank strikes an object.

The tank or hull may be damaged if the tank strikes an object.

If a steel tank is installed on a wooden or FRP vessel, take appropriate measures to prevent electrolytic corrosion.

Electrolytic corrosion can damage the hull.

Be sure that the power supply is compatible with the voltage rating of the equipment.

Connection of an incorrect power supply can cause fire or equipment damage. The voltage rating of the equipment appears on the label above the power connector.

CAUTION

Ground the equipment to prevent electrical shock and mutual interference.

Observe the following compass safe distances:

 

Standard

Steering

 

 

 

Display unit

0.9 m

0.68 m

for CSH-23

 

 

 

 

 

Display unit

1.70 m

1.30 m

for CSH-24

 

 

 

Processor

1.70 m

1.05 m

unit

 

 

 

 

 

i

Image 3
Contents Color Scanning Sonar 00080806903 Safety Instructions Table of Contents System Configuration Equipment Lists Optional Equipment Location of hull unit Mounting the Hull Unit and Receiver UnitMaintenance space, example sonar compartment Shortening the retraction tank Installation Method Xdcr TravelHow to install reinforcement ribs Remarks for installation of retraction tankInstallation of hull unit Installing hull unit on retraction tankFastening receiver unit to hull unit Installing stays anti-vibration measureMounting the display unit/sub-display unit Mounting the Display Unit/Sub-display UnitMounting the Transmitter Unit Mounting the Interface UnitMounting the FNZ Joint Box 12 Location of ground terminals on equipment Grounding the EquipmentCable Configuration WiringHow to use the crimping tool How to use the pin extractor How to Use the Crimping Tool, Pin ExtractorLocation ConnectorsFabricating Cable, Assembling Connectors Clamping the cable Assembling connector NSC-253P CN-A15Fabricating cable 54-038-000-601/SC CN-E1 Assembling 38P connectorFabricating cable DPYCY-4connected to terminal board TB-E1 Fabricating cable 10S1259 connected terminal board TB-E114 Fabricating cable 54-038-000-601/SC Fabricating cable 54-038-000-601/SC CN-B2, CN-B3, CN-B416 Clamping the cable Fabricating cable 10S1259 connected to terminal board TB-B119 Assembling 38P connector 22 Fabricating cable 10S1259 23 Receiver unit, rear view Connection of Transducer CablesConnections for true motion and target lock Connection of Interface Unit CS-120ASpeed pulse signal Connections for ES picture and FNZ markers Data Data Source WiringFabrication, assembling 10P and 7P connectors DIP switch setting Connection of Sub-display Unit CSH-236/236F OptionConnections Connections Synchronizing Transmission with Other Sonars, Echo SoundersMenu setting Connections for interlocking functions Interlocking Operation with Other Sonar37 Connections for interlocking remote control Connections for interlocking remote controlChanging Power Specifications Hull Unit Check Adjustment and CheckInit SET/TEST Menu Heading AdjustmentDIP Switch Setting in the Display Unit DIP switch setting Setting and Adjustment of the Interface Unit CS-120AOFF Interface unit 10P0047 adjustmentPriority for data Adjustment of signal level R36, R56LC fixing position priority Processor Unit CSH-235/235F Blackbox Type for CSH-23/23F Mounting procedureProtective earth Connectors for MonitorProcessor unit right side, cover removed Packing List Spare Parts List for 工事材料表 Page Page 000-070-208 10CJ-X-9302 000-070-209 10CJ-X-9303 Furuno Electric CO .,LTD Installation Materials Name Outline Hole Plug Page 006-959-800-00 10CC-X-9401 Panel Screw アイボルト 受信装置用 For Power Supply Unit アース板 電源装置用 006-030-650-00 10CJ-X-9402 For Transceiver Unit 貼りマーク 送信装置工材 コンタクト ピン(8017 電源装置工材 Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Dec Page Page Page Page Page Page Page Color Scanning Sonar Page Color Scanning Sonar Processor Unit Interface Unit