Furuno CSH-24 Connection of Sub-display Unit CSH-236/236F Option, Connections, DIP switch setting

Page 34

4.7Connection of Sub-display Unit CSH-236/236F (Option)

The Sub-Display Unit CSH-236/236F is the same as the Display Unit CSH-230/230F in terms of outline dimension and control panel layout. It controls the sonar at a place remote from the display unit while observing picture on the screen. One sub-display unit can be connected to three display units.

Note: The Sub-Display Unit can be connected to CSH-23/23F only.

Connections

Refer to the interconnection diagram at the end of this manual.

Note: One sub-display unit can be connected to three sonars, but different models cannot be connected.

DIP switch setting

Set DIP switch S1 on the RDCB Board (10P6724) in the sub-display unit as follows:

10P6724

CN-A3 CN-A2 CN-A1

(CH-3) (CH-2) (CH-1)

S1

SW No.

Used for

Function

 

 

 

1

Display unit on CH-1

ON: Turning on sub-display unit automatically

2

Display unit on CH-2

turns on display unit.

3

Display unit on CH-3

Don’t set OFF because the system doesn’t work.

 

 

 

 

 

4

Display unit on CH-1

ON: Turning on display unit automatically

5

Display unit on CH-2

turns on sub-display unit.

6

Display unit on CH-3

OFF: Sub-display unit is not turned on when display

 

 

unit is turned on.

 

 

 

7

Not used.

Used in remote display unit. Set to ON in sub-display

 

unit.

 

 

 

 

 

8

Not used.

 

Figure 4-31 DIP switch setting on RDCB board in the sub-display unit

Note: To have both the display unit and sub-display unit turned on when either unit is turned on, turn on SW #1 and #4.

29

Image 34
Contents Color Scanning Sonar 00080806903 Safety Instructions Table of Contents System Configuration Equipment Lists Optional Equipment Mounting the Hull Unit and Receiver Unit Location of hull unitMaintenance space, example sonar compartment Installation Method Xdcr Travel Shortening the retraction tankRemarks for installation of retraction tank How to install reinforcement ribsInstalling hull unit on retraction tank Installation of hull unitInstalling stays anti-vibration measure Fastening receiver unit to hull unitMounting the Display Unit/Sub-display Unit Mounting the display unit/sub-display unitMounting the Interface Unit Mounting the Transmitter UnitMounting the FNZ Joint Box Grounding the Equipment 12 Location of ground terminals on equipmentWiring Cable ConfigurationHow to Use the Crimping Tool, Pin Extractor How to use the crimping tool How to use the pin extractorConnectors LocationFabricating Cable, Assembling Connectors Assembling connector NSC-253P CN-A15 Clamping the cableAssembling 38P connector Fabricating cable 54-038-000-601/SC CN-E1Fabricating cable 10S1259 connected terminal board TB-E1 Fabricating cable DPYCY-4connected to terminal board TB-E1Fabricating cable 54-038-000-601/SC CN-B2, CN-B3, CN-B4 14 Fabricating cable 54-038-000-601/SCFabricating cable 10S1259 connected to terminal board TB-B1 16 Clamping the cable19 Assembling 38P connector 22 Fabricating cable 10S1259 Connection of Transducer Cables 23 Receiver unit, rear viewConnection of Interface Unit CS-120A Connections for true motion and target lockSpeed pulse signal Connections for ES picture and FNZ markers Wiring Data Data SourceFabrication, assembling 10P and 7P connectors Connection of Sub-display Unit CSH-236/236F Option DIP switch settingConnections Synchronizing Transmission with Other Sonars, Echo Sounders ConnectionsMenu setting Interlocking Operation with Other Sonar Connections for interlocking functionsConnections for interlocking remote control 37 Connections for interlocking remote controlChanging Power Specifications Adjustment and Check Hull Unit CheckHeading Adjustment Init SET/TEST MenuDIP Switch Setting in the Display Unit Setting and Adjustment of the Interface Unit CS-120A DIP switch settingInterface unit 10P0047 adjustment OFFAdjustment of signal level R36, R56 Priority for dataLC fixing position priority Mounting procedure Processor Unit CSH-235/235F Blackbox Type for CSH-23/23FConnectors for Monitor Protective earthProcessor unit right side, cover removed Packing List Spare Parts List for 工事材料表 Page Page 000-070-208 10CJ-X-9302 000-070-209 10CJ-X-9303 Furuno Electric CO .,LTD Installation Materials Name Outline Hole Plug Page 006-959-800-00 10CC-X-9401 Panel Screw アイボルト 受信装置用 For Power Supply Unit アース板 電源装置用 006-030-650-00 10CJ-X-9402 For Transceiver Unit 貼りマーク 送信装置工材 コンタクト ピン(8017 電源装置工材 Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Dec Page Page Page Page Page Page Page Color Scanning Sonar Page Color Scanning Sonar Processor Unit Interface Unit

CSH-24F, CSH-23F, CSH-23, CSH-24 specifications

Furuno, a leader in marine electronics, has developed a range of advanced marine radar systems known as the CSH series. The CSH-24, CSH-23, CSH-23F, and CSH-24F are particularly notable for their innovative technologies, designed to enhance navigational safety and operational efficiency for vessels of various sizes.

The CSH-24 and CSH-23 models are known for their impressive 24 GHz and 23 GHz frequency bands, offering high-resolution imagery and enhanced target detection capabilities. These radars utilize Furuno’s digital signal processing technology, which significantly improves target discrimination, even in cluttered environments. This feature is invaluable for navigational safety, especially in busy waterways or coastal areas.

One of the key highlights of the CSH series is its advanced Automatic Radar Plotting Aid (ARPA) functionality, which enables the proactive monitoring of marine traffic. With the ability to track multiple targets simultaneously, mariners can make more informed decisions, avoiding potential collisions and ensuring smoother navigation. Additionally, the systems provide enhanced Tracking History that allows users to analyze target movements over time.

The CSH-24F and CSH-23F models incorporate Furuno's cutting-edge features, including Fast Target Tracking and Target Predictive Motion, which further enhances reactive capabilities. These radars also offer an intuitive user interface, making it easy to operate and customize settings to fit specific navigational requirements. The displays are designed for readability, even under challenging lighting conditions, thanks to advanced anti-glare technologies.

Built with ruggedness in mind, the CSH series is designed to withstand harsh marine environments. The robust construction and weatherproof design ensure that the systems perform reliably, regardless of sea conditions. Moreover, these radar systems are compatible with a range of marine integration options, allowing for seamless connectivity with other onboard navigation equipment.

In summary, the Furuno CSH-24, CSH-23, CSH-23F, and CSH-24F radars embody a blend of advanced technology, robust design, and user-friendly interfaces. These systems stand out in the marine electronics market for their reliability and precision, making them an excellent choice for maritime professionals seeking enhanced safety and efficiency on the water.