Hoshizaki 73180 service manual Storage Bin Drain

Page 57

12)Open the water supply line shut-off valve.

13)Plug the unit back in. Move the power switch to the "ON" position and allow the icemaker to run. Check for leaks.

14)After 30 minutes, move the power switch to the "OFF" position. Unplug the unit.

15)Pour warm water into the storage bin to melt all of the ice, then clean the storage bin liner, door liner, and door gasket with a neutral cleaner. Rinse thoroughly after cleaning.

16)Plug the unit back in. Move the power switch to the "ON" position to start the automatic icemaking process.

C. Storage Bin Drain

In some conditions, slime may build up inside the storage bin drain and prevent water from draining properly. To prevent this buildup, perform the following procedure once every 3 months or as often as necessary for conditions.

NOTICE

If the storage bin drain becomes clogged, water could build up in the bin and overflow, leading to costly water damage.

1)Move the power switch to the "OFF" position. WARNING! To reduce the risk of electric shock, do not touch the power switch with damp hands.

2)Remove all ice from the storage bin.

3)Mix a batch of sanitizing solution by diluting 1.25 fl. oz. (37 ml or 2.5 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach) with 2.5 gal. (9.5 l) of warm water.

Using a chlorine test strip or other method, confirm that you have a concentration of about 200 ppm.

4)Slowly pour the sanitizing solution into the storage bin.

5)After all of the solution has drained, clean the storage bin liner with a neutral cleaner. Rinse thoroughly with clean water.

6)Move the power switch to the "ON" position to start the automatic icemaking process.

57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents 100BAF-DS 100BAF-AD 100BAF-ADDS Hoshizaki AMERICA, INC Contents Page Important Safety Information Page Auxiliary Codes A-1 and Earlier Specifications 100BAFAuxiliary Codes A-2 and Later 100BAF-DS 100BAF-DS, 2. Auxiliary Codes A-2 and Later 100BAF-AD 100BAF-AD, 2. Auxiliary Codes A-2 and Later 100BAF-ADDS 100BAF-ADDS, 2. Auxiliary Codes A-2 and Later Front II. General Information ConstructionAuxiliary Codes Rear Auxiliary CodesIcemaking Unit Freeze Cycle Sequence of OperationFill Cycle Auxiliary Codes A-1 and Earlier Auxiliary Codes A-2 and Later Auxiliary Codes A-2 and Later Wiring DiagramIcemaker with Optional Drain Pump HS-0248 100BAF Series Performance DataIV. Service Diagnosis Diagnostic ProcedureIce Production Check Page Auxiliary Codes A-2 and Later Bin Control Check Float Switch Check Lower Float white Plastic Retainer Clip Float Switch CleaningOptional Drain Pump HS-0248 OverviewDrain Pump Check Priming Instructions Float Switch Cleaning No Ice Production Possible Cause Startup Diagnostic ChartsShutdown Fill Cycle and Refill Cycle Shutdown Removal and Replacement of Components Service for Refrigerant LinesRefrigerant Recovery Evacuation and Recharge R-134a BrazingComponent Important Notes for Component ReplacementRemoval and Replacement of Evaporator Assembly Components Upper Bearing Wear Check Removal and Replacement of Extruding Head Removal and Replacement of Auger Removal and Replacement of Evaporator Page 5b. Lower Housing Page VI. Maintenance Frequency Area Task Maintenance ScheduleCleaning Solution Cleaning and Sanitizing InstructionsPage Sanitizing Solution Page Cleaning Solution Page Sanitizing Solution Storage Bin Drain Condenser Auxiliary Codes A-1 and Earlier Skip to step VII. Preparing the Icemaker for Periods of Non-UseVIII. Disposal
Top Page Image Contents