Creative E-MU manual Edit Parameters, PGM Send on Recall

Page 33

Basic Operations

Edit Parameters

These parameters are accessed via the Edit button. See “Editing Patch and Device Settings” on page 31 for detailed instructions about how to access the Edit mode.

PGM Send on Recall

Every Xboard patch stores a MIDI program change number (as well as Bank Select MSB and LSB settings) for each of the 16 MIDI channels. The “PGM Send On Recall” setting is a master switch which enables or disables transmission of the stored MIDI program change settings when a patch is recalled.

Select on to transmit the program changes, etc. stored in a patch when that patch is recalled. This allows you to reconfigure all of your MIDI instruments at once by simply recalling that patch. Select oFF if you don’t want the stored program changes transmitted on patch recall.

This feature has a couple of tricky aspects which you need to be aware of in order to use it as intended:

•In addition to the master on/off switch, there is also an on/off switch per MIDI channel. When the master switch is set to on, program changes will be sent upon patch recall only on channels whose per-channel on/off switch is also set to on in the patch. This allows you to restrict program change sends to only the desired channels. However, unlike the master switch, these per- channel switch settings can only be modified using the Xboard Control editor application. Since all of these switches are set to off by default, full setup of this feature is possible only using that application.

•The master and per-channel on/off settings, as well as the program change and bank select numbers, are stored in and recalled from patches. They are not global settings and can be different from one patch to the next. Since they are applied immediately following recall of a patch, these settings must already be stored in a patch in order to have any effect upon what happens when the patch is recalled, and will apply only to that patch. It follows that the patch must be stored again anytime these settings get changed – otherwise, any changed settings will be lost.

Xboard

33

Image 33

Contents Xboard Asia Pacific Africa, Middle East MU World Headquarters MU SystemsEurope Japan Creative Media K. KTable of Contents Back Panel Description Powering the Xboard Xboard 61 Panel ControlsBasic Operations MU Xboard Control AppendixIndex MU Systems Introduction Requirements Hardware InstallationOn a PC On a MacConnecting the Xboard to your Computer USB ConnectionMidi Connection Midi Midi InterfaceSoftware Installation Macintosh OSWindows Uninstalling all Audio Drivers and Applications Click Start „ Settings „ Control PanelWindows XP To confirm the problem, do the following TroubleshootingLost Communication Wrong Driver in Windows XP or WindowsIntroduction Introduction Click Have Disk Windows 2000 „ You may recover by doing the followingMidi Indicators Data Entry / Master Volume SliderMain Panel Controls EditEnter Store PatchOctave Down Octave UpLatch Mode Channel Control ModeMidi Channel Select Knob BypassChannel Controller mode Normal mode3D Midi and Nrpn mode Controller KnobsXboard 61 Panel Controls Zones EnablePatch Select / Numeric Keypad Keyboard Zones ButtonsProgram Change Mode Using the Numeric KeypadBack Panel Description Inserting Batteries into the Xboard Powering the XboardTo Insert Batteries This Side Not UsedBasic Operations To Select a Patch Using the Main PanelEntering Data Selecting and Storing PatchesChanging the Midi Channel To Select a Patch Using Direct Patch Select Buttons XboardTo Store a Patch To Change the Midi ChannelTransposing the Keyboard Channel Control ModeChanging Controller CC Channel Numbers To Change Controller CC Channel NumbersTo Enable or Disable the Zones Function To Select 16 Channel Control ModeTo Enable or Disable a Specific Zone Working With ZonesTo Select Latch Mode Latch Mode, Zones DisabledLatch Mode, Zones Enabled Snap ShotTo Set the Keyboard Range of Latched Notes Bypass Mode Editing Patch and Device SettingsTo Edit a Setting Scrolling Text Display Editing Patch Device SettingsPGM Send on Recall Edit ParametersSend Program Change Bank Sel MSBTo Send an External Program Change Xboard Program Change PGM Browse Mode Bank Sel LSBTo Browse Midi Program Changes Save CC Value in Patch CC Send On RecallAftertouch On/Off Semitone TransposeTips for Use… Velocity Curve Select Channel CC NumberLatch High/Low Note X1 and X2 Functions X1 Menu ItemsTo Select one of the X1 or X2 Functions CCM To Calibrate the Pitch Wheel To Calibrate Aftertouch using One or More KeysLow Velocity = 1 default X2 Menu Items Definitions MU Xboard ControlZone Xboard Control WindowDragging and Dropping Bank ViewChanging the Order of Patches Loading Bank or Patch FilesBasic Operation DesktopDevice Changing Settings Patch Modified IndicatorPatch Name Storing PatchesMidi Controller Knob Settings Initial Knob SettingsPatch Editor Tab Midi Channel CC TypeKeyboard Settings Basic Midi ChannelMidi Channel Number Per Control Channel Control Mode CC Number Pitch Wheel SettingsMod Wheel Settings Page Program Change per Midi Channel Send Controller Values on Patch RecallVelocity Curve Select Zones Graphical Display Zones TabGlobal Zones Settings Zones SettingsController Range Individual Zones Settings Controller Range Menu Items BackupsPreferences DeviceLoad From File Loading and SavingSave Patch Save RevertRevert StoreView Menu Edit MenuDevice Menu Help MenuAppendix Midi BackgroundMidi Channels & Continuous Controllers Midi Program Change Commands Footpedal WiringMidi Bank Select Commands FootpedalMidi Information Transmitted Recognized Remarks Midi Implementation ChartControl # Function Transmitted Recognized Remarks Midi Implementation Chart part 2 ControllersMidi Implementation Chart part 2 Controllers Nrpn LSB Nrpn MSB Appendix MU Systems Numerics IndexMidi Index