Creative E-MU manual Ccm

Page 40

Basic Operations

Pedal (PEd)

This function sets up the Footswitch / Footpedal input to accept a switch or a variable pedal control input.

•SuS = Sustain or footswitch input. In this mode, the Xboard automatically senses the footswitch polarity on power up (either normally-open, or normally-closed). Because of the automatic sensing feature, you should not hold down the footswitch during power up or the switch action will be reversed.

•ctL = Control Pedal. The Xboard accepts control pedals wired as shown on page 65.

Indicators (ind)

The decimal points in the LED indicate USB and MIDI activity. Select on or oFF. 1st = USB In; 2nd = USB Out; 3rd = MIDI Out.

Zones On/Off Status Display (Zod)

Select on or oFF.

If on, when you select a new patch, the Edit LED display shows a message indicating whether zones enabled or disabled in the new patch. This is especially useful for the Xboard 25 and Xboard 49, since they don’t have a Zones Enable button.

Patch Buttons Program Change Mode Auto-Disable (PbM) Select on or oFF.

With this setting on, the Program Change Mode button turns off automatically after you send a program change, returning the numeric keypad to Direct Patch Select Mode.

With this setting off, the Numeric Keypad remains in Program Change mode after you send a program change.

Calibrate Sub-Menu (CAL)

When you select CAL and press Enter, you are taken to the CAL sub-menu, which contains calibration functions. To select a function, use the data slider to select a Calibration function, and press Enter. To cancel, press Home.

CCM

This feature enables you to calibrate any control on your Xboard, one at a time, optimizing your Xboard’s action for your playing technique.

After you select the CCM function and press Enter, all LEDs on the Xboard turn off (except the display, which says “adjust a control”). This is Calibration Standby mode. What you do next depends on which control you want to calibrate.

E-MU Systems

40

Image 40

Contents Xboard MU World Headquarters MU Systems Asia Pacific Africa, Middle EastEurope Japan Creative Media K. KTable of Contents Xboard 61 Panel Controls Back Panel Description Powering the XboardBasic Operations Appendix MU Xboard ControlIndex MU Systems Introduction Hardware Installation RequirementsOn a PC On a MacUSB Connection Connecting the Xboard to your ComputerMidi Connection Midi Interface MidiMacintosh OS Software InstallationWindows Click Start „ Settings „ Control Panel Uninstalling all Audio Drivers and ApplicationsWindows XP Troubleshooting To confirm the problem, do the followingLost Communication Wrong Driver in Windows XP or WindowsIntroduction Introduction Windows 2000 „ You may recover by doing the following Click Have DiskData Entry / Master Volume Slider Midi IndicatorsMain Panel Controls EditStore Patch EnterOctave Down Octave UpChannel Control Mode Latch ModeMidi Channel Select Knob BypassNormal mode Channel Controller mode3D Midi and Nrpn mode Controller KnobsZones Enable Xboard 61 Panel ControlsPatch Select / Numeric Keypad Keyboard Zones ButtonsUsing the Numeric Keypad Program Change ModeBack Panel Description Powering the Xboard Inserting Batteries into the XboardTo Insert Batteries This Side Not UsedTo Select a Patch Using the Main Panel Basic OperationsEntering Data Selecting and Storing PatchesTo Select a Patch Using Direct Patch Select Buttons Xboard Changing the Midi ChannelTo Store a Patch To Change the Midi ChannelChannel Control Mode Transposing the KeyboardChanging Controller CC Channel Numbers To Change Controller CC Channel NumbersTo Select 16 Channel Control Mode To Enable or Disable the Zones FunctionTo Enable or Disable a Specific Zone Working With ZonesLatch Mode, Zones Disabled To Select Latch ModeSnap Shot Latch Mode, Zones EnabledTo Set the Keyboard Range of Latched Notes Editing Patch and Device Settings Bypass ModeTo Edit a Setting Editing Patch Device Settings Scrolling Text DisplayEdit Parameters PGM Send on RecallBank Sel MSB Send Program ChangeTo Send an External Program Change Xboard Bank Sel LSB Program Change PGM Browse ModeTo Browse Midi Program Changes CC Send On Recall Save CC Value in PatchSemitone Transpose Aftertouch On/OffTips for Use… Channel CC Number Velocity Curve SelectLatch High/Low Note X1 Menu Items X1 and X2 FunctionsTo Select one of the X1 or X2 Functions CCM To Calibrate Aftertouch using One or More Keys To Calibrate the Pitch WheelLow Velocity = 1 default X2 Menu Items MU Xboard Control DefinitionsXboard Control Window ZoneBank View Dragging and DroppingChanging the Order of Patches Loading Bank or Patch FilesDesktop Basic OperationDevice Patch Modified Indicator Changing SettingsPatch Name Storing PatchesInitial Knob Settings Midi Controller Knob SettingsPatch Editor Tab CC Type Midi ChannelBasic Midi Channel Keyboard SettingsMidi Channel Number Per Control Pitch Wheel Settings Channel Control Mode CC NumberMod Wheel Settings Page Send Controller Values on Patch Recall Program Change per Midi ChannelVelocity Curve Select Zones Tab Zones Graphical DisplayZones Settings Global Zones SettingsController Range Individual Zones Settings Controller Range Backups Menu ItemsPreferences DeviceLoading and Saving Load From FileSave Patch Save RevertStore RevertEdit Menu View MenuDevice Menu Help MenuMidi Background AppendixMidi Channels & Continuous Controllers Footpedal Wiring Midi Program Change CommandsMidi Bank Select Commands FootpedalMidi Implementation Chart Midi Information Transmitted Recognized RemarksMidi Implementation Chart part 2 Controllers Control # Function Transmitted Recognized RemarksMidi Implementation Chart part 2 Controllers Nrpn LSB Nrpn MSB Appendix MU Systems Index NumericsMidi Index