Creative E-MU manual Keyboard Settings, Basic Midi Channel, Midi Channel Number Per Control

Page 51

E-MU Xboard Control

NRPN Mode

For devices that support NRPNs (Non-Registered Parameter Numbers). NRPN messages can span across two controller numbers (LSB and MSB), increasing the range of potential values. A complete NRPN message consists of NRPN parameters LSB and MSB (set in the Xboard Control) and NRPN data LSB and MSB (sent by the Continuous Controller).

NOTE: NRPN mode does not have an Initial Controller setting.

LThis value (0-127) defines NRPN parameter LSB (Least Significant Byte).

MThis value (0-127) defines NRPN parameter MSB (Most Significant Byte).

Keyboard Settings

Basic MIDI Channel:

The keyboard always transmits on the basic MIDI channel. The controller knobs, wheels and footpedal/footswitch also transmit on the Basic MIDI channel, except when the “MIDI Channel Number Per Control” option is selected.

MIDI Channel Number Per Control

The keyboard ALWAYS transmits on this MIDI channel. The knobs also transmit on this channel, except when “MIDI Channel” Number Per Control” is selected.

Normally, the keyboard and all controllers are transmitted on the Basic MIDI channel. This option allows you to select any MIDI channel for each knob, the two wheels and the footpedal. The example below shows how you might control four parameters on four different synthesizers using the sixteen controller knobs.

Volume on MIDI Ch. 1-4

Filter Cutoff on MIDI Ch. 1-4

Env. Decay on MIDI Ch. 1-4

LFO Rate on MIDI Ch. 1-4

Xboard

51

Image 51

Contents Xboard Japan Creative Media K. K MU World Headquarters MU SystemsAsia Pacific Africa, Middle East EuropeTable of Contents Back Panel Description Powering the Xboard Xboard 61 Panel ControlsBasic Operations MU Xboard Control AppendixIndex MU Systems Introduction On a Mac Hardware InstallationRequirements On a PCConnecting the Xboard to your Computer USB ConnectionMidi Connection Midi Midi InterfaceSoftware Installation Macintosh OSWindows Uninstalling all Audio Drivers and Applications Click Start „ Settings „ Control PanelWindows XP Wrong Driver in Windows XP or Windows TroubleshootingTo confirm the problem, do the following Lost CommunicationIntroduction Introduction Click Have Disk Windows 2000 „ You may recover by doing the followingEdit Data Entry / Master Volume SliderMidi Indicators Main Panel ControlsOctave Up Store PatchEnter Octave DownKnob Bypass Channel Control ModeLatch Mode Midi Channel SelectController Knobs Normal modeChannel Controller mode 3D Midi and Nrpn modeKeyboard Zones Buttons Zones EnableXboard 61 Panel Controls Patch Select / Numeric KeypadProgram Change Mode Using the Numeric KeypadBack Panel Description This Side Not Used Powering the XboardInserting Batteries into the Xboard To Insert BatteriesSelecting and Storing Patches To Select a Patch Using the Main PanelBasic Operations Entering DataTo Change the Midi Channel To Select a Patch Using Direct Patch Select Buttons XboardChanging the Midi Channel To Store a PatchTo Change Controller CC Channel Numbers Channel Control ModeTransposing the Keyboard Changing Controller CC Channel NumbersWorking With Zones To Select 16 Channel Control ModeTo Enable or Disable the Zones Function To Enable or Disable a Specific ZoneTo Select Latch Mode Latch Mode, Zones DisabledLatch Mode, Zones Enabled Snap ShotTo Set the Keyboard Range of Latched Notes Bypass Mode Editing Patch and Device SettingsTo Edit a Setting Scrolling Text Display Editing Patch Device SettingsPGM Send on Recall Edit ParametersSend Program Change Bank Sel MSBTo Send an External Program Change Xboard Program Change PGM Browse Mode Bank Sel LSBTo Browse Midi Program Changes Save CC Value in Patch CC Send On RecallAftertouch On/Off Semitone TransposeTips for Use… Velocity Curve Select Channel CC NumberLatch High/Low Note X1 and X2 Functions X1 Menu ItemsTo Select one of the X1 or X2 Functions CCM To Calibrate the Pitch Wheel To Calibrate Aftertouch using One or More KeysLow Velocity = 1 default X2 Menu Items Definitions MU Xboard ControlZone Xboard Control WindowLoading Bank or Patch Files Bank ViewDragging and Dropping Changing the Order of PatchesBasic Operation DesktopDevice Storing Patches Patch Modified IndicatorChanging Settings Patch NameMidi Controller Knob Settings Initial Knob SettingsPatch Editor Tab Midi Channel CC TypeKeyboard Settings Basic Midi ChannelMidi Channel Number Per Control Channel Control Mode CC Number Pitch Wheel SettingsMod Wheel Settings Page Program Change per Midi Channel Send Controller Values on Patch RecallVelocity Curve Select Zones Graphical Display Zones TabGlobal Zones Settings Zones SettingsController Range Individual Zones Settings Controller Range Device BackupsMenu Items PreferencesSave Revert Loading and SavingLoad From File Save PatchRevert StoreHelp Menu Edit MenuView Menu Device MenuAppendix Midi BackgroundMidi Channels & Continuous Controllers Footpedal Footpedal WiringMidi Program Change Commands Midi Bank Select CommandsMidi Information Transmitted Recognized Remarks Midi Implementation ChartControl # Function Transmitted Recognized Remarks Midi Implementation Chart part 2 ControllersMidi Implementation Chart part 2 Controllers Nrpn LSB Nrpn MSB Appendix MU Systems Numerics IndexMidi Index