Creative E-MU manual Program Change per Midi Channel, Send Controller Values on Patch Recall

Page 54

E-MU Xboard Control

Send Controller Values on Patch Recall

When this parameter is set to On, the stored initial value (position) settings of the 16 Controller Knobs, the Pitch Wheel, the Mod Wheel and the Footpedal will be transmitted when the patch is recalled via the Xboard front panel. When set to Off, the stored controller initial value settings will not be transmitted when the patch is recalled via the Xboard front panel. This setting affects only the behavior of the Xboard itself. Selecting patches in Xboard Control does not cause controller messages to be sent from either the host computer or the Xboard.

Note: Pressing the Xboard’s Snapshot button will immediately send the patch’s stored controller values, regardless of whether this parameter is On or Off.

Velocity Curve Select

This function selects one of the eight velocity curves to customize the velocity response of the keyboard. Select a synthesizer preset that has velocity programmed (such as a piano), then choose a curve that gives you the best control.

Click on an image to select the desired velocity curve for the patch. See page 38 for descriptions of the curves.

Program Change per MIDI Channel

Master Enable

In this example, five program changes will be transmitted.

The Xboard has the ability to transmit a MIDI Program Change on each of the 16 MIDI channels whenever a patch is recalled via the Xboard front panel. This feature allows you to set up all your MIDI instruments for a performance by simply selecting a patch on the Xboard. Program Bank MSB and LSB numbers are also transmitted. See “MIDI Bank Select Commands” on page 65 for more infor- mation.

The Master Enable button turns Program Change transmit on or off for the patch as a whole. (Note: this setting is the same as the Xboard “PGM Send On Recall” setting described on page 33.) The enable buttons over each channel slot allow you to select which channels will transmit program change messages when the patch is recalled. Note that the per-channel enable settings can be edited only via Xboard Control.

E-MU Systems

54

Image 54

Contents Xboard Europe MU World Headquarters MU SystemsAsia Pacific Africa, Middle East Japan Creative Media K. KTable of Contents Back Panel Description Powering the Xboard Xboard 61 Panel ControlsBasic Operations MU Xboard Control AppendixIndex MU Systems Introduction On a PC Hardware InstallationRequirements On a MacConnecting the Xboard to your Computer USB ConnectionMidi Connection Midi Interface MidiSoftware Installation Macintosh OSWindows Uninstalling all Audio Drivers and Applications Click Start „ Settings „ Control PanelWindows XP Lost Communication TroubleshootingTo confirm the problem, do the following Wrong Driver in Windows XP or WindowsIntroduction Introduction Windows 2000 „ You may recover by doing the following Click Have DiskMain Panel Controls Data Entry / Master Volume SliderMidi Indicators EditOctave Down Store PatchEnter Octave UpMidi Channel Select Channel Control ModeLatch Mode Knob Bypass3D Midi and Nrpn mode Normal modeChannel Controller mode Controller KnobsPatch Select / Numeric Keypad Zones EnableXboard 61 Panel Controls Keyboard Zones ButtonsUsing the Numeric Keypad Program Change ModeBack Panel Description To Insert Batteries Powering the XboardInserting Batteries into the Xboard This Side Not UsedEntering Data To Select a Patch Using the Main PanelBasic Operations Selecting and Storing PatchesTo Store a Patch To Select a Patch Using Direct Patch Select Buttons XboardChanging the Midi Channel To Change the Midi ChannelChanging Controller CC Channel Numbers Channel Control ModeTransposing the Keyboard To Change Controller CC Channel NumbersTo Enable or Disable a Specific Zone To Select 16 Channel Control ModeTo Enable or Disable the Zones Function Working With ZonesLatch Mode, Zones Disabled To Select Latch ModeLatch Mode, Zones Enabled Snap ShotTo Set the Keyboard Range of Latched Notes Bypass Mode Editing Patch and Device SettingsTo Edit a Setting Editing Patch Device Settings Scrolling Text DisplayEdit Parameters PGM Send on RecallSend Program Change Bank Sel MSBTo Send an External Program Change Xboard Program Change PGM Browse Mode Bank Sel LSBTo Browse Midi Program Changes CC Send On Recall Save CC Value in PatchAftertouch On/Off Semitone TransposeTips for Use… Velocity Curve Select Channel CC NumberLatch High/Low Note X1 and X2 Functions X1 Menu ItemsTo Select one of the X1 or X2 Functions CCM To Calibrate Aftertouch using One or More Keys To Calibrate the Pitch WheelLow Velocity = 1 default X2 Menu Items MU Xboard Control DefinitionsXboard Control Window ZoneChanging the Order of Patches Bank ViewDragging and Dropping Loading Bank or Patch FilesBasic Operation DesktopDevice Patch Name Patch Modified IndicatorChanging Settings Storing PatchesMidi Controller Knob Settings Initial Knob SettingsPatch Editor Tab CC Type Midi ChannelKeyboard Settings Basic Midi ChannelMidi Channel Number Per Control Channel Control Mode CC Number Pitch Wheel SettingsMod Wheel Settings Page Program Change per Midi Channel Send Controller Values on Patch RecallVelocity Curve Select Zones Tab Zones Graphical DisplayZones Settings Global Zones SettingsController Range Individual Zones Settings Controller Range Preferences BackupsMenu Items DeviceSave Patch Loading and SavingLoad From File Save RevertStore RevertDevice Menu Edit MenuView Menu Help MenuAppendix Midi BackgroundMidi Channels & Continuous Controllers Midi Bank Select Commands Footpedal WiringMidi Program Change Commands FootpedalMidi Implementation Chart Midi Information Transmitted Recognized RemarksMidi Implementation Chart part 2 Controllers Control # Function Transmitted Recognized RemarksMidi Implementation Chart part 2 Controllers Nrpn LSB Nrpn MSB Appendix MU Systems Index NumericsMidi Index