Creative E-MU manual X2 Menu Items

Page 43

Basic Operations

Aftertouch Sense Level Limit Low (ALo)

Select a Value between 0 and 998 (default value: 80).

This sets the lower limit for the Aftertouch sensing circuit. It is thus the threshold setting, which determines how much pressure you have to apply in order to make the Xboard begin ending Aftertouch messages. If this setting is adjusted too low, you may find it difficult to play the keyboard without sending Aftertouch messages.

Aftertouch Sense Level Limit High (AHi)

Select a Value between 1 and 999 (default value: 600).

This sets the upper limit for the Aftertouch sensing circuit. It thus determines how much pressure you have to apply in order to make the Xboard send a maximum- value Aftertouch message. If this setting is adjusted too high, you may find it impossible to produce a maximum-value Aftertouch message, regardless of how hard you press.

Note that increasing the Low setting beyond the existing High setting will result in the High setting being changed automatically so that it remains higher than the new Low setting, and vice versa. Setting the aftertouch sense level limit values too close to one another will result in jumpy, "either/or" response (either no aftertouch or maximum aftertouch).

X2 Menu Items

The following is a description of the items located in the X2 menu.

Zones Enable in Patch (ZoE)

Select on or oFF.

Turns all zones on or off in the active patch. For the Xboard 61, this serves the exact same function as the Zones Enable button. It is most useful on the Xboard 25 or Xboard 49, since they don’t have a Zones Enable button.

Xboard

43

Image 43
Contents Xboard Japan Creative Media K. K MU World Headquarters MU SystemsAsia Pacific Africa, Middle East EuropeTable of Contents Xboard 61 Panel Controls Back Panel Description Powering the XboardBasic Operations Appendix MU Xboard ControlIndex MU Systems Introduction On a Mac Hardware InstallationRequirements On a PCUSB Connection Connecting the Xboard to your ComputerMidi Connection Midi Midi InterfaceMacintosh OS Software InstallationWindows Click Start „ Settings „ Control Panel Uninstalling all Audio Drivers and ApplicationsWindows XP Wrong Driver in Windows XP or Windows TroubleshootingTo confirm the problem, do the following Lost CommunicationIntroduction Introduction Click Have Disk Windows 2000 „ You may recover by doing the followingEdit Data Entry / Master Volume SliderMidi Indicators Main Panel ControlsOctave Up Store PatchEnter Octave DownKnob Bypass Channel Control ModeLatch Mode Midi Channel SelectController Knobs Normal modeChannel Controller mode 3D Midi and Nrpn modeKeyboard Zones Buttons Zones EnableXboard 61 Panel Controls Patch Select / Numeric KeypadProgram Change Mode Using the Numeric KeypadBack Panel Description This Side Not Used Powering the XboardInserting Batteries into the Xboard To Insert BatteriesSelecting and Storing Patches To Select a Patch Using the Main PanelBasic Operations Entering DataTo Change the Midi Channel To Select a Patch Using Direct Patch Select Buttons XboardChanging the Midi Channel To Store a PatchTo Change Controller CC Channel Numbers Channel Control ModeTransposing the Keyboard Changing Controller CC Channel NumbersWorking With Zones To Select 16 Channel Control ModeTo Enable or Disable the Zones Function To Enable or Disable a Specific ZoneTo Select Latch Mode Latch Mode, Zones DisabledSnap Shot Latch Mode, Zones EnabledTo Set the Keyboard Range of Latched Notes Editing Patch and Device Settings Bypass ModeTo Edit a Setting Scrolling Text Display Editing Patch Device SettingsPGM Send on Recall Edit ParametersBank Sel MSB Send Program ChangeTo Send an External Program Change Xboard Bank Sel LSB Program Change PGM Browse ModeTo Browse Midi Program Changes Save CC Value in Patch CC Send On RecallSemitone Transpose Aftertouch On/OffTips for Use… Channel CC Number Velocity Curve SelectLatch High/Low Note X1 Menu Items X1 and X2 FunctionsTo Select one of the X1 or X2 Functions CCM To Calibrate the Pitch Wheel To Calibrate Aftertouch using One or More KeysLow Velocity = 1 default X2 Menu Items Definitions MU Xboard ControlZone Xboard Control WindowLoading Bank or Patch Files Bank ViewDragging and Dropping Changing the Order of PatchesDesktop Basic OperationDevice Storing Patches Patch Modified IndicatorChanging Settings Patch NameInitial Knob Settings Midi Controller Knob SettingsPatch Editor Tab Midi Channel CC TypeBasic Midi Channel Keyboard SettingsMidi Channel Number Per Control Pitch Wheel Settings Channel Control Mode CC NumberMod Wheel Settings Page Send Controller Values on Patch Recall Program Change per Midi ChannelVelocity Curve Select Zones Graphical Display Zones TabGlobal Zones Settings Zones SettingsController Range Individual Zones Settings Controller Range Device BackupsMenu Items PreferencesSave Revert Loading and SavingLoad From File Save PatchRevert StoreHelp Menu Edit MenuView Menu Device MenuMidi Background AppendixMidi Channels & Continuous Controllers Footpedal Footpedal WiringMidi Program Change Commands Midi Bank Select CommandsMidi Information Transmitted Recognized Remarks Midi Implementation ChartControl # Function Transmitted Recognized Remarks Midi Implementation Chart part 2 ControllersMidi Implementation Chart part 2 Controllers Nrpn LSB Nrpn MSB Appendix MU Systems Numerics IndexMidi Index