Creative E-MU manual X1 and X2 Functions, X1 Menu Items, To Select one of the X1 or X2 Functions

Page 39

Basic Operations

X1 and X2 Functions

The X1 key accesses the X1 functions. These are global functions that affect all patches. For example, if Pedal is set to Sus, it will remain so for all patches.

•Mid - Out or Thru - When Out is selected, the MIDI output transmits local data from the keyboard and knobs. When Thru is selected, the MIDI output transmits data from the host application.

•PEd - Selects between a footswitch (SuS) or a continuous footpedal (ctL)

•ind - Turns the decimal point USB/MIDI indicators on or off. See page 17.

•Zod - Turns the zones status message on or off.

•PbM - Determines the behavior of the Numeric Keypad after you send a program change.

•CAL - The Calibration sub-menu. The functions here allow you to make very specific calibrations. These settings are for advanced users.

The X2 key accesses the X2 functions. These are global functions which affect only the active patch. For example, if you turn Zones off it will remain so for only the active patch.

•ZoE - Enables and disables Zones functions in the active patch.

To Select one of the X1 or X2 Functions:

1.Press the Edit button. The Edit LED illuminates.

2.Select X1 or X2.

3.Adjust the data slider or use the Octave Transpose buttons to view the functions.

4.Press Enter to select the desired function.

5.Select the desired value using the data slider or the Octave Transpose buttons (except with CAL).

6.Press Enter to confirm your selection. Press Home to cancel the operation.

X1 Menu Items

The following is a description of the items located in the X1 menu.

MIDI (Mid)

The Xboard can function as a MIDI interface between your computer applications and external MIDI gear. When set to Thru, MIDI data from your computer appli- cation is transmitted on the Xboard’s MIDI output jack. When Out is selected, the MIDI output transmits local data from the keyboard and knobs.

Xboard keyboard and controller data is NOT transmitted from the MIDI output when this function is set to Thru. (Keyboard/Controller data is always sent via USB.)

Xboard

39

Image 39

Contents Xboard Japan Creative Media K. K MU World Headquarters MU SystemsAsia Pacific Africa, Middle East EuropeTable of Contents Back Panel Description Powering the Xboard Xboard 61 Panel ControlsBasic Operations MU Xboard Control AppendixIndex MU Systems Introduction On a Mac Hardware InstallationRequirements On a PCConnecting the Xboard to your Computer USB ConnectionMidi Connection Midi Midi InterfaceSoftware Installation Macintosh OSWindows Uninstalling all Audio Drivers and Applications Click Start „ Settings „ Control PanelWindows XP Wrong Driver in Windows XP or Windows TroubleshootingTo confirm the problem, do the following Lost CommunicationIntroduction Introduction Click Have Disk Windows 2000 „ You may recover by doing the followingEdit Data Entry / Master Volume SliderMidi Indicators Main Panel ControlsOctave Up Store PatchEnter Octave DownKnob Bypass Channel Control ModeLatch Mode Midi Channel SelectController Knobs Normal modeChannel Controller mode 3D Midi and Nrpn modeKeyboard Zones Buttons Zones EnableXboard 61 Panel Controls Patch Select / Numeric KeypadProgram Change Mode Using the Numeric KeypadBack Panel Description This Side Not Used Powering the XboardInserting Batteries into the Xboard To Insert BatteriesSelecting and Storing Patches To Select a Patch Using the Main PanelBasic Operations Entering DataTo Change the Midi Channel To Select a Patch Using Direct Patch Select Buttons XboardChanging the Midi Channel To Store a PatchTo Change Controller CC Channel Numbers Channel Control ModeTransposing the Keyboard Changing Controller CC Channel NumbersWorking With Zones To Select 16 Channel Control ModeTo Enable or Disable the Zones Function To Enable or Disable a Specific ZoneTo Select Latch Mode Latch Mode, Zones DisabledLatch Mode, Zones Enabled Snap ShotTo Set the Keyboard Range of Latched Notes Bypass Mode Editing Patch and Device SettingsTo Edit a Setting Scrolling Text Display Editing Patch Device SettingsPGM Send on Recall Edit ParametersSend Program Change Bank Sel MSBTo Send an External Program Change Xboard Program Change PGM Browse Mode Bank Sel LSBTo Browse Midi Program Changes Save CC Value in Patch CC Send On RecallAftertouch On/Off Semitone TransposeTips for Use… Velocity Curve Select Channel CC NumberLatch High/Low Note X1 and X2 Functions X1 Menu ItemsTo Select one of the X1 or X2 Functions CCM To Calibrate the Pitch Wheel To Calibrate Aftertouch using One or More KeysLow Velocity = 1 default X2 Menu Items Definitions MU Xboard ControlZone Xboard Control WindowLoading Bank or Patch Files Bank ViewDragging and Dropping Changing the Order of PatchesBasic Operation DesktopDevice Storing Patches Patch Modified IndicatorChanging Settings Patch NameMidi Controller Knob Settings Initial Knob SettingsPatch Editor Tab Midi Channel CC TypeKeyboard Settings Basic Midi ChannelMidi Channel Number Per Control Channel Control Mode CC Number Pitch Wheel SettingsMod Wheel Settings Page Program Change per Midi Channel Send Controller Values on Patch RecallVelocity Curve Select Zones Graphical Display Zones TabGlobal Zones Settings Zones SettingsController Range Individual Zones Settings Controller Range Device BackupsMenu Items PreferencesSave Revert Loading and SavingLoad From File Save PatchRevert StoreHelp Menu Edit MenuView Menu Device MenuAppendix Midi BackgroundMidi Channels & Continuous Controllers Footpedal Footpedal WiringMidi Program Change Commands Midi Bank Select CommandsMidi Information Transmitted Recognized Remarks Midi Implementation ChartControl # Function Transmitted Recognized Remarks Midi Implementation Chart part 2 ControllersMidi Implementation Chart part 2 Controllers Nrpn LSB Nrpn MSB Appendix MU Systems Numerics IndexMidi Index