Creative E-MU manual Send Program Change, Bank Sel MSB, To Send an External Program Change Xboard

Page 34

Basic Operations

Send Program Change

This function sends MIDI program changes to your external gear on the currently selected Basic MIDI channel. (At the same time, it edits the program change number for the current MIDI channel in the active patch. See “PGM Send on Recall” on page 33 for more info.)

Note that the program change send includes a send of Bank Select MSB and Bank Select LSB according to the settings for those parameters on the same MIDI channel in the current patch. See page 34.

To Send an External Program Change Via the Main Control Panel:

1.Press the Edit button.

2.Press the Send Prog Change keyboard key.

3.Select the desired program change number from 0-127 using the Data Slider, Octave Transpose buttons, or Numeric Keyboard Keys.

4.Press Enter to send the program change.

5.Press Home to exit without sending the program change. (This also leaves the program change setting for the current MIDI channel unmodified in the active patch.)

To Send an External Program Change (Xboard 61):

1.Make sure the Program Change Mode button’s LED is lit. If not, press the button to light it.

2.Use the Direct Patch Select numerical buttons to enter a one- to three-digit program change number. Use the button labeled “10” to enter a “0.”

3.Do one of the following:

•If Zones are enabled, press the corresponding Zone button for the MIDI channel you want to send the Program change across. If you want to send the Program Change over the current MIDI channel, press Enter or the Program Change Mode button (they will be blinking).

•If Zones are not enabled, press Enter or the Program Change Mode button (they will both be blinking).

Bank Sel MSB

This parameter allows you to select the MIDI Bank Select MSB (most significant byte) that will be used when sending program changes via the Prog Change, PGM Browse Mode or PGM Send On Recall features.

Select a Bank MSB from 0-127. Note that this merely edits the Bank Select MSB setting for the current MIDI channel in the active patch. It does not cause a MIDI message to be sent immediately.

For more information on MIDI Bank Select commands, see page 65.

E-MU Systems

34

Image 34

Contents Xboard Europe MU World Headquarters MU SystemsAsia Pacific Africa, Middle East Japan Creative Media K. KTable of Contents Xboard 61 Panel Controls Back Panel Description Powering the XboardBasic Operations Appendix MU Xboard ControlIndex MU Systems Introduction On a PC Hardware InstallationRequirements On a MacUSB Connection Connecting the Xboard to your ComputerMidi Connection Midi Interface MidiMacintosh OS Software InstallationWindows Click Start „ Settings „ Control Panel Uninstalling all Audio Drivers and ApplicationsWindows XP Lost Communication TroubleshootingTo confirm the problem, do the following Wrong Driver in Windows XP or WindowsIntroduction Introduction Windows 2000 „ You may recover by doing the following Click Have DiskMain Panel Controls Data Entry / Master Volume SliderMidi Indicators EditOctave Down Store PatchEnter Octave UpMidi Channel Select Channel Control ModeLatch Mode Knob Bypass3D Midi and Nrpn mode Normal modeChannel Controller mode Controller KnobsPatch Select / Numeric Keypad Zones EnableXboard 61 Panel Controls Keyboard Zones ButtonsUsing the Numeric Keypad Program Change ModeBack Panel Description To Insert Batteries Powering the XboardInserting Batteries into the Xboard This Side Not UsedEntering Data To Select a Patch Using the Main PanelBasic Operations Selecting and Storing PatchesTo Store a Patch To Select a Patch Using Direct Patch Select Buttons XboardChanging the Midi Channel To Change the Midi ChannelChanging Controller CC Channel Numbers Channel Control ModeTransposing the Keyboard To Change Controller CC Channel NumbersTo Enable or Disable a Specific Zone To Select 16 Channel Control ModeTo Enable or Disable the Zones Function Working With ZonesLatch Mode, Zones Disabled To Select Latch ModeSnap Shot Latch Mode, Zones EnabledTo Set the Keyboard Range of Latched Notes Editing Patch and Device Settings Bypass ModeTo Edit a Setting Editing Patch Device Settings Scrolling Text DisplayEdit Parameters PGM Send on RecallBank Sel MSB Send Program ChangeTo Send an External Program Change Xboard Bank Sel LSB Program Change PGM Browse ModeTo Browse Midi Program Changes CC Send On Recall Save CC Value in PatchSemitone Transpose Aftertouch On/OffTips for Use… Channel CC Number Velocity Curve SelectLatch High/Low Note X1 Menu Items X1 and X2 FunctionsTo Select one of the X1 or X2 Functions CCM To Calibrate Aftertouch using One or More Keys To Calibrate the Pitch WheelLow Velocity = 1 default X2 Menu Items MU Xboard Control DefinitionsXboard Control Window ZoneChanging the Order of Patches Bank ViewDragging and Dropping Loading Bank or Patch FilesDesktop Basic OperationDevice Patch Name Patch Modified IndicatorChanging Settings Storing PatchesInitial Knob Settings Midi Controller Knob SettingsPatch Editor Tab CC Type Midi ChannelBasic Midi Channel Keyboard SettingsMidi Channel Number Per Control Pitch Wheel Settings Channel Control Mode CC NumberMod Wheel Settings Page Send Controller Values on Patch Recall Program Change per Midi ChannelVelocity Curve Select Zones Tab Zones Graphical DisplayZones Settings Global Zones SettingsController Range Individual Zones Settings Controller Range Preferences BackupsMenu Items DeviceSave Patch Loading and SavingLoad From File Save RevertStore RevertDevice Menu Edit MenuView Menu Help MenuMidi Background AppendixMidi Channels & Continuous Controllers Midi Bank Select Commands Footpedal WiringMidi Program Change Commands FootpedalMidi Implementation Chart Midi Information Transmitted Recognized RemarksMidi Implementation Chart part 2 Controllers Control # Function Transmitted Recognized RemarksMidi Implementation Chart part 2 Controllers Nrpn LSB Nrpn MSB Appendix MU Systems Index NumericsMidi Index