Pioneer SVM-1000 Fader Curve Selection, Selecting Stereo or Monaural, Microphone Input

Page 14

BASIC OPERATIONS

 

MONO/STEREO

MIC1 LEVEL

HI

MIC2 LEVEL

 

HI, LOW

 

MIC

 

CUE

 

MONO SPLIT/STEREO

 

MIXING

BOOTH MONITOR

LEVEL

CH FADER CURVE

Selecting Stereo or Monaural

When the MONO/STEREO switch is set to [MONO], the audio master output becomes a monaural combination of L+R channels.

Microphone Input

1To use a microphone, set the MIC switch to [ON] or [TALK OVER].

When set to [TALK OVER], any time a sound of –15 dB (default setting) or more is input, all sound sources other than the microphone are attenuated by 20 dB (default setting). These default values can be changed in the hardware setup (P. 42).

2Use the MIC 1 LEVEL dial to adjust the sound volume of MIC 1, and use the MIC 2 LEVEL dial to adjust the sound volume of MIC 2.

3Use the microphone equalizer dials (HI, LOW) to adjust the tone of the microphone sound.

•The microphone equalizer function operates simultaneously on microphone 1 and 2.

Booth Monitor Output

1Use the BOOTH MONITOR level dial to adjust the sound volume.

•The BOOTH MONITOR level dial can be used to adjust the sound volume independently of the AUDIO MASTER LEVEL dial.

•Use the hardware setup (P. 42) to set whether or not the microphone sound is to be output to the booth monitor.

Headphones Output

1Use the headphone CUE buttons (channels 1 to 4, MASTER, EFFECT CUE) to select the source.

•The selected CUE button lights brightly.

2Set the HEADPHONES (MONO SPLIT/STEREO) switch.

•When set to the [MONO SPLIT] position, the sound selected with the headphone CUE button is output to the left channel, and the master sound is output to the right channel (only when MASTER CUE button is set to ON).

•When set to the [STEREO] position, the sound selected with the headphone CUE button is output in stereo.

3When [MONO SPLIT] is selected, use the HEADPHONES MIXING dial to adjust the balance of sound between the left channel (sound selected with the headphone CUE button), and the right channel (master sound).

•When the HEADPHONES MIXING dial is rotated clockwise (toward [MASTER]), the master output (only when the MASTER CUE button is ON) increases; when rotated counterclockwise (toward [CUE]), the sound selected with the headphone CUE button increases.

CROSS FADER CURVE

4Use the HEADPHONES LEVEL dial to adjust the headphones’ sound volume.

•Rotate the HEADPHONES LEVEL dial to adjust the sound level.

•When the Effect mode select button (P. 17) is set to [V] mode, effect sounds will not be output even if the EFFECT CUE button is pressed.

FADER CURVE SELECTION

The response of sound volume change to the fader control can be set in three types.

Use the CH FADER CURVE switch to select the desired channel fader response curve.

The sound volume and video level changes as follows:

•At the left setting, the curve operates to produce a rapid rise as the channel fader approaches its distant position.

•At the right setting, the curve operates to produce an even, neutral rise throughout the channel fader’s movement.

•At the middle setting, an intermediate curve is produced, midway between the two curves noted above.

•This setting applies equally to channels 1 to 4.

Use the CROSS FADER CURVE switch to select the cross fader curve response.

Sound volume changes as follows:

•At the left setting, the curve produces a rapid signal rise. (As soon as the cross fader lever leaves the [A] side, the [B] channel sound is produced.)

•At the right setting, the curve operates to produce an even, neutral rise throughout the cross fader’s movement.

•At the middle setting, an intermediate curve is produced, midway between the two curves noted above.

•This setting produces equal curve effects for both sides A and B.

The video level is as noted above only when the video cross fader’s video mix effect is set to [FADE].

14

En

Page 13 Page 15
Image 14
Page 13 Page 15
Contents SVM-1000 POWER-CORD Caution Ventilation CautionContents Channnel Music and Video Synchromix Confirm Features AccessoriesDigital sound/video system for high quality sound and image Installing the SVM-1000 in an EIA rack Improved design and operability for new club cultureMaster COMPONENT, COMPOSITE, S-VIDEO Names and Functions of PartsConnection Panel Operation Panel Talk OverLine StereoPhono DigitalChannel fader curve switch CH Fader Curve Master level indicator Master L, RBooth Monitor level control dial Video EQ button ON/OFF, SET UPConnecting other line level output devices Connecting InputsConnecting an analog turntable ConnectionsConnecting Outputs External video connector Connecting Microphone and HeadphonesConnecting the Power Cord HeadphonesBasic Operations Selecting Stereo or Monaural Headphones OutputFader Curve Selection Microphone InputOperating the Video Cross Fader Using the Video Control FunctionsOperating the Video Channel Switch When Fader AV Sync is on Operating in the Video Solo ModeVideo MIX Effects Chart When Fader AV Sync is OFFWhen master monitor is on Using the Effect FunctionUsing Beat Effects When master monitor is offVideo effect pattern Manually entering the BPM using the TAP buttonUsing the visualizer ParameterPattern Using Touch EffectsWhen master monitor is off When master monitor is on Select an effect from the effect select buttonsText Edit Using Text EffectsText Bank Text bank Text BOX DISPLAYING/HIDING the Master MonitorUSB keyboard Caps /Parameter Description of the effect Beat button parameter Effect ListBeat effects *1 TIME/PARAMETER LEVEL/DEPTHOriginal Touch effects *1 Touched DescriptionShorter cycle length Sound Left to lower the pitch Effect. When dial is Rotated fully Spot Drop *3 TIME/PARAMETER Text effectsCharacter Jpeg Viewer Setup Using the Jpeg ViewerBefore Using the Jpeg Viewer Using a USB memory deviceOperating in Auto Mode Using a Jpeg file by assigning it to a channelOperating in Manual Mode Loading Jpeg files to the SVM-1000Deleting Jpeg files downloaded to the Jpeg BOX Operating in Fader ModePress the Clear button once again to leave this mode Turning the Equalizer ON/OFF SET UP the Video EQVideo Equalizer Function Touch ExitFader Start Function Using the Cross Fader to Start PlaybackUsing the Channel Fader to Start Playback Cross Fader Start Play and Back CUE PlaySet up Midi Perform Utility SetupMidi Settings Fader CF Assign Video Trim Audio Trim CH2 MID LOW CUE BTN Midi Code ListMSB LSB Video Trim Audio Trim CH1 MID LOW CUE BTN Fader CF Assign Video Trim Audio Trim CH3 MID LOW CUE BTNMSB Booth Monitor AUTO/TAP BTNFLANGER, PHASER, Filter TAP BTNBeat Effect BTN Effect Text Effect BTN Category DelayPhaser BTN Touch Effect BTNZoom BTN Cross Fader Switch BTNRandom BTN Rotation BTNVideo monitor setup Perform Video Monitor SetupKeyboard Language Setup Keyboard language setupMIC Setting Hardware SetupSystem Settings Initiate hardware setupLCD Settings Master OUT SettingsMonitor OUT Settings Ending Hardware SET UP Touch Panel SettingsReturning to Default Settings TOP PanelDepth TroubleshootingSymptom Possible Cause Remedy About the LCD Screen About Miniature Fluorescent Tube TechnologySpecifications OtherCustomer Support Division 800 782 Pioneer Electronics of Canada, IncPioneer Electronics USA, INC BOX 1760, Long Beach
Top Page Image Contents