Solid State Logic 82S6PC1010C manual Centuri Processor

Page 19

Section 4		System Components

The Centuri Processor

The Centuri processor is a 15U high 600mm deep rack unit. Cards are fitted to the front and rear of the chassis so space for access is essential. See page 10 for chassis dimensions and minimum service clearance.

At the front of the processor are located the plug-in PSU units. One unit is capable of powering the system. The panel below the power supplies is fitted with either a 250Mb Zip drive or an SD memory card reader. This is used to transfer system software onto the internal hard disk. This panel may also be fitted with the optional MO drive for project storage.

Below the drives is the front card-cage which has space for 11 plug-in cards, numbered from left to right. The cards are arranged as follows:

Slots 1–4 Channel DSP cards.

Slot 5 Always fitted with a DSP card for the Centre-Section mixes.

Slot 6 Reserved for future expansion.

Slots 7–10 I/O cards – micamp cards (digital/MADI cards to special order only)1.

Slot 11 Always fitted with the system disc card; unless the dual-redundant disc option is specified.

There rear of the processor has space for 12 plug-in cards. Note that these slots are numbered from right to left. Slots 1–4 Available for I/O cards (analogue, digital and MADI).

Slot 5 Always fitted with the console’s Routing/Link card.

Slot 6 Reserved for the optional GPI/O card.

Slots 7–10 I/O cards – analogue, digital and MADI (mic cards to special order only)1.

Slot 11 Always fitted with the Console-Interface card.

Slot 12 Always fitted with the CPU card.

Note that front and rear mounting I/O cards, although functionally identical, are physically different so it is not possible to exchange cards between back and front after specification.

Below the rear card-cage are connectors for MIDI funct ions and anot her labelled ’Expansion’. Thes e are not implemented in the C100 system.

(1) Specifying rear mounted micamp cards or front mounted digital/MADI cards will extend the order lead time.

Page 15

Image 19

Contents Installation Guide Page Solid State Logic Solid State Logic Contents Introduction Voltage Selection and Fusing Safety ConsiderationsElectrical Safety Warning Installation InstructionsMains Isolation and Over-Current Protection Safety Earth ConnectionMains Supply and Phases Physical SafetyFCC Certification CE CertificationCommissioning Pre Installation InformationServices provided by SSL WarrantyAcoustic Isolation Physical RequirementsConsole Control Surface Rack Mounting Equipment Centuri, NetBridge and StageboxesChannel Footprint Side Profile Showing Service AccessAir Conditioning Requirements Service AccessCable Ducting SB Crate side view Showing Card Access Centuri Processor Crate side view Showing Card AccessGrounding Power Connections Mains Input Voltage & CurrentTechnical Requirements Video Sync SourceEVS C100 Channel Bay LayoutC100 Console System ComponentsCenturi Processor Crate Rear View Centuri Processor Crate Front ViewCenturi Processor Console Routing/Link Card Interface System DiskCenturi Console Interface Card Centuri DSP CardCenturi Disk Card Centuri CPU Card+5V Mic Input Analogue I/O Digital I/OCenturi Madi Card Copper version Centuri Micamp CardCenturi Analogue I/O Card Centuri Digital I/O CardMorse Router Morse 3U Stagebox SB Stagebox Front ViewMorse System option SB Stagebox optionNetBridge Rear View NetBridge Front ViewNetBridge PSU Voltage Selection NetBridge option Location Of Bellypanel USB Connectors TFT External Input option External Keyboard / Trackball optionsScript Tray option Loudspeaker Shelf optionCenturi Mains Inlet Panel Console Mains Inlet PanelNetBridge Rear Panel Power Supply Connections Installation WiringAudio Console Connector Panel Control Surface Wiring Block DiagramCPU Card Control Card Centuri to Console Surface Connections CPU Card PSU Status Wiring DiagramSync Source PSU StatusAnalogue I/O Card Micamp Input CardAnalogue input/output Card SSL ref MicAmp Card SSL refMadi I/O Card Copper version Digital I/O Card D25 versionDigital Input/Output Card 75Ω SSL ref XJ Digital Input/Output Card 110Ω SSL ref XFGPI I/O Card GPI Output circuit GPI I/O SSL ref XAGPI Input circuit SB CPU Card Fibre Link Connectors and PanelsSB Cabling Diagrams Centuri Link CardStageboxes & Fibre Links TCP/IP NetBridge InstallationConnection NetBridge InstallationAccess Remote DiagnosticsC100 Console Talkback system Block DiagramCenturi Chassis Talkback Connections Talkback and OscillatorOscillator Connections Meter and Phasescope wiring RTW Meter and Phasescope wiring MSD 600CCenturi Crate Meters and Phasescope Gold is 1.9 times heavier than Lead Appendix a Specifications Centuri Processor Crate Net Bridge SB Micamp Rack Hood Free Socket Appendix B Connector DetailsDL 96-Pin Hood Varicon 56-pin PlugSocket25-way XLR 3-PinDIN 5-Pin Type MultipinMeter Inputs Analogue Appendix C Connector Pinouts C100 ConsoleMSD Diag Diagnostics / Remote Control Phase Scope DigitalExpansion Connector Pinouts Centuri ProcessorMachine Control TimecodeTtya TTYD, Ttyf Ttyh RS422 SerialTtye RS232 Mic in 1 Mic Input Card ‘908Analogue in / Analogue OUT Analogue I/O Card ‘904BNC Breakout Panel Digital I/O Card ‘902AES/EBU In 1-8 9-16, 17-24 AES/EBU Out 1-8 9-16, 17-24GPI Outputs 1 12 13 24, 25 36, 37 48, 49 GPI I/O Card ‘907Terminal Connector Pinouts NetBridgeNetBridge Diagnostic Cable Serial 1-8 RS232C100 Installation Guide Appendix D Audio Interfacing Connecting to Unbalanced EquipmentBalanced Circuits C100 Installation Guide Appendix E Environmental Specification +4dBu = 1.229V rms dBu = 0.775V rms. -6dBu = 0.388V rms Design Requirements for a Flightcase Appendix F Additional Information for Installing StageboxesThis page is blank intentionally Cables and Accessories by Part Description Appendix G Cables and accessoriesMiscellaneous/Hardware Description SSL Part No Video & SyncAppendix G Part Numbers More Notes