Sony SRP-X500P manual Input Volume 3rd-8th byte, Master Volume Level 9th byte

Page 26

SRP-X500P RS-232C Interface Manual

♦PROJECTOR PROTOCOL SWITCH (1st byte)

SYSTEM TYPE SWITCH (2nd byte)

Shows the position of the PROJECTOR PROTOCOL selector or the SYSTEM TYPE selector on the front panel of the SRP-X500P.

The parameters and the switch position are shown in the following table.

SWITCH

0	0x30 (‘0’)
1	0x31 (‘1’)
2	0x32 (‘2’)
3	0x33 (‘3’)
4	0x34 (‘4’)
5	0x35 (‘5’)
6	0x36 (‘6’)
7	0x37 (‘7’)
8	0x38 (‘8’)
9	0x39 (‘9’)
A	0x3A (‘:’)
B	0x3B (‘;’)
C	0x3C (‘<‘)
D	0x3D (‘=‘)
E	0x3E (‘>‘)
F	0x3F (‘?’)

♦INPUT VOLUME (3rd-8th byte)

Shows the setting of the input level controls on the front panel of the SRP-X500P.

Byte	Parameter
1st	MIC 1/WL 1 INPUT VOLUME
2nd	MIC 2/WL 2 INPUT VOLUME
3rd	MIC 3 INPUT VOLUME
4th	MIC 4 INPUT VOLUME
5th	LINE INPUT VOLUME
6th	AV/RGB INPUT VOLUME

The correspondence of the parameter with the level setting is the same as that of the FADER parameter of the INPUT FADER command (page 7).

♦MASTER VOLUME LEVEL (9th byte)

Shows the setting of the MASTER control on the front panel of the SRP-X500P.

The correspondence of the parameter with the level setting is the same as that of the FADER parameter of the INPUT FADER command (page 7).

♦REMOTE 1-6 LEVEL (10th-15th byte)

Shows the level of the REMOTE 1-6 faders.

The correspondence of the parameter with the level setting is the same as that of the LEVEL parameter of the REMOTE 1-6 LEVEL command (page 10).

Page 26/43

Image 26

Contents SRP-X500P Table of Contents 3 4 Connecting the SRP-X500P to a ComputerAbout This Manual Communication Protocol RS-232C indicatorCommunication Format Handshake Codes Communication Packet FormatBasic Control Commands 1 AV/RGB Input Select 0x43 0x53 0x45 0x4C ‘CSEL’Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’ Return packet formatInput Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’ Fader 1st-6th byteFader 1st-8th byte Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’Output Fader Request 0x52 0x50 0x4D 0x40 ‘RPM@’ Remote Remote 1-6 Level 0x43 0x4C 0x56 0x4C ‘CLVL’Channel 1st byte Level 2nd byte Remote 1-6 Level 2nd-7th byte Master Volume UP 0x43 0x4C 0x56 0x2B ‘CLV+’Master Volume Level 1st byte Master Volume Down 0x43 0x4C 0x56 0x2D ‘CLV-’ Master Volume Stop 0x43 0x4C 0x56 0x53 ‘CLVS’Muting 0x43 0x4D 0x55 0x54 ‘CMUT’ Muting 2nd byteSpeaker Output Muting 2nd byte Muting Parameter Request 0x52 0x4D 0x55 0x54 ‘RMUT’Input Muting 1st byte Remote Muting 5th byte Line Output Muting 3rd byteMaster Muting 4th byte MasterProjector ON/STANDBY 0x43 0x50 0x4A 0x50 ‘CPJP’ Projector Control Request 1st byteScene Recall Request 1st byte Projector ON/STANDBY Indicator 1st byteScene Recall 0x43 0x52 0x43 0x4C ‘CRCL’ Scene Recall RequestScene Recall Parameter Request 0x52 0x52 0x43 0x4C ‘RRCL’ Scene No st byteIndex Status Acquisition CommandsIndex Request 0x52 0x50 0x4D 0x44 ‘RPMD’ Level Meter Parameter Request 0x52 0x4D 0x54 0x52 ‘RMTR’ Level Meter 1st-16th byte To acquire status of single item To acquire the status of all items Parameters Remote 1-6 Level 10th-15th byte Input Volume 3rd-8th byteMaster Volume Level 9th byte Input Muting 30th byte Input Level 16th-21st byteOutput Level 22nd-29th byte Line Output Muting Output Muting 31st and 32nd byteSpeaker Output Muting Master Muting 33rd byte+48V Switch 38th byte RF/AF Indicator 36th byteWL Indicator 37th byte MIC 1-4 Trim 39th-42nd byteAV/RGB Trim 44th-48th byte REF Indicator 49th byteLine Trim 43rd byte FR 50th-53rd byte FR Setup Status 54th and 55th byteSetup Channel Speaker Output Level 57th, 58th byte Setup StatusAV/RGB Input Select 56th byte Speaker Output CH1/2 LevelLevel Meter 60th-75th byte IR Output Mode Indicator 59th byteClip Indicator 77th byte Protection 76th byteProjector ON/STANDBY Indicator 80th byte Temperature 78th and 79th byteTemperature EMG Muting 83rd byteLevel Scene No th byteParallel Input 85th-94th byte Parallel Output 95th and 96th byteFAN Motor 97th byte Master Volume Control 98th byteOutput OUT6 OUT5 OUT4 OUT3 OUT2Gain Reduction 99th-108th byte AGC Gain ControlCompressor Gain Reduction Information Request 0x52 0x50 0x4D 0x45 ‘RPME’ Maintenance Information CommandsInformation SETUPDATE2005/01/23 InformationMaintenance Information Read Write Maintenance Information Read WriteMaintenance Information Read only Maintenance Information Read onlyVersion Version Request 0x52 0x56 0x45 0x52 ‘RVER’Version Factory Preset 0x43 0x52 0x53 0x54 ‘CRST’

Related manuals

Manual 6 pages 29.24 Kb