Sony SRP-X500P manual IR Output Mode Indicator 59th byte, Level Meter 60th-75th byte

Page 33

SRP-X500P RS-232C Interface Manual

♦IR OUTPUT MODE INDICATOR (59th byte)

Shows the status of the IR OUTPUT MODE button on the front panel of the SRP-X500P.

The correspondence of the parameter with the IR OUTPUT MODE button status is shown in the following table.

IR OUTPUT MODE

Normal operation (The button is turned off.)	0x30 (‘0’)
Transmission wait status (The button lights up.)	0x31 (‘1’)
Transmission in progress (The button flashes.)	0x32 (‘2’)

♦LEVEL METER (60th-75th byte)

Shows the level meter indication of the input/output channels.

The configuration of the parameter and the correspondence of the parameter with the level meters are the same as those of the LEVEL METER PARAMETER REQUEST command (page 21).

♦PROTECTION (76th byte)

Shows the protection circuit status of the power amplifiers in 8 bits of data.

MSB							LSB
bit7	bit6	bit5	bit4	bit3	bit2	bit1	bit0
0	1	0	CH3/4	CH3/4	CH1/2	CH1/2	DC
			TEMP.	IC	TEMP.	IC	DETECTION

・TEMP.

The bit for the power amplifier is 0 when the protection circuit is not activated and 1 when the protection circuit is activated due to increased internal temperature of the SRP-X500P.

・IC

The bit for the power amplifier is 0 when the protection circuit incorporated in the IC is not activated and 1 when the protection circuit incorporated in the IC is activated.

・DC DETECTION

When the protection circuit is not activated, The bit for the power amplifier is 0. When the DC power voltage is output to the SPEAKER CH terminals and the protection circuit is activated, the bit for the power amplifier is 1.

♦CLIP INDICATOR (77th byte)

Shows the CLIP indicator status in 8 bits of data.

The parameter shown for this command is the status of the CLIP indicators in the BLOCK screen and the OVER VIEW screen of the SRP-X500P Manager.

When the CLIP indicator is turned off, the corresponding bit is 0. When the CLIP indicator is turned on, the corresponding bit is 1.

MSB							LSB
bit7	bit6	bit5	bit4	bit3	bit2	bit1	bit0
0	1	0	0	CH 4	CH 3	CH 2	CH 1

Page 33/43

Image 33

Contents SRP-X500P Table of Contents Connecting the SRP-X500P to a Computer About This Manual3 4 RS-232C indicator Communication FormatCommunication Protocol Communication Packet Format Handshake Codes1 AV/RGB Input Select 0x43 0x53 0x45 0x4C ‘CSEL’ Basic Control CommandsReturn packet format Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’Fader 1st-6th byte Input Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’ Output Fader Request 0x52 0x50 0x4D 0x40 ‘RPM@’Fader 1st-8th byte Remote 1-6 Level 0x43 0x4C 0x56 0x4C ‘CLVL’ Channel 1st byteRemote Level 2nd byte Master Volume UP 0x43 0x4C 0x56 0x2B ‘CLV+’ Master Volume Level 1st byteRemote 1-6 Level 2nd-7th byte Master Volume Stop 0x43 0x4C 0x56 0x53 ‘CLVS’ Master Volume Down 0x43 0x4C 0x56 0x2D ‘CLV-’Muting 2nd byte Muting 0x43 0x4D 0x55 0x54 ‘CMUT’Muting Parameter Request 0x52 0x4D 0x55 0x54 ‘RMUT’ Input Muting 1st byteSpeaker Output Muting 2nd byte Master Muting 4th byte Line Output Muting 3rd byteRemote Muting 5th byte MasterProjector Control Request 1st byte Projector ON/STANDBY 0x43 0x50 0x4A 0x50 ‘CPJP’Scene Recall 0x43 0x52 0x43 0x4C ‘CRCL’ Projector ON/STANDBY Indicator 1st byteScene Recall Request 1st byte Scene Recall RequestScene No st byte Scene Recall Parameter Request 0x52 0x52 0x43 0x4C ‘RRCL’Status Acquisition Commands Index Request 0x52 0x50 0x4D 0x44 ‘RPMD’Index Level Meter Parameter Request 0x52 0x4D 0x54 0x52 ‘RMTR’ Level Meter 1st-16th byte To acquire status of single item To acquire the status of all items Parameters Input Volume 3rd-8th byte Master Volume Level 9th byteRemote 1-6 Level 10th-15th byte Input Level 16th-21st byte Output Level 22nd-29th byteInput Muting 30th byte Speaker Output Muting Output Muting 31st and 32nd byteLine Output Muting Master Muting 33rd byteWL Indicator 37th byte RF/AF Indicator 36th byte+48V Switch 38th byte MIC 1-4 Trim 39th-42nd byteREF Indicator 49th byte Line Trim 43rd byteAV/RGB Trim 44th-48th byte FR Setup Status 54th and 55th byte Setup ChannelFR 50th-53rd byte AV/RGB Input Select 56th byte Setup StatusSpeaker Output Level 57th, 58th byte Speaker Output CH1/2 LevelClip Indicator 77th byte IR Output Mode Indicator 59th byteLevel Meter 60th-75th byte Protection 76th byteTemperature Temperature 78th and 79th byteProjector ON/STANDBY Indicator 80th byte EMG Muting 83rd byteParallel Input 85th-94th byte Scene No th byteLevel Parallel Output 95th and 96th byteOutput Master Volume Control 98th byteFAN Motor 97th byte OUT6 OUT5 OUT4 OUT3 OUT2AGC Gain Control Gain Reduction 99th-108th byteCompressor Gain Reduction Information SETUPDATE2005/01/23 Maintenance Information CommandsInformation Request 0x52 0x50 0x4D 0x45 ‘RPME’ InformationMaintenance Information Read Write Maintenance Information Read WriteMaintenance Information Read only Maintenance Information Read onlyVersion Request 0x52 0x56 0x45 0x52 ‘RVER’ VersionVersion Factory Preset 0x43 0x52 0x53 0x54 ‘CRST’

Related manuals

Manual 6 pages 29.24 Kb