Sony manual About This Manual, Connecting the SRP-X500P to a Computer, 3 4

Page 3

SRP-X500P RS-232C Interface Manual

1. Overview

1.1 About This Manual

This manual is the Interface Manual for the Sony SRP-X500P Digital Powered Mixer. The protocol explained in this manual is designed for controlling the SRP-X500P Digital Powered Mixer from an externally connected computer. This manual should be used together with the Operating Instructions and the User’s Guide.

Note

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by purchasers of the equipment described in this manual.

Sony Corporation prohibits the duplication or use of any portion of this manual without expressed written permission from Sony Corporation for any purpose other than the operation or maintenance of the equipment described in this manual.

In this manual, numeric values are indicated as follows:
Unmarked numbers	: decimal numbers
Numbers prefaced by “0x” (e.g., 0x10)	: hexadecimal numbers
Numbers enclosed by single quotation marks (‘ ’)	: ASCII-converted hexadecimal numbers code

1.2 Connecting the SRP-X500P to a Computer

Connect the COM port of the computer to the REMOTE RS-232C connector of the SRP-X500P. The REMOTE RS-232C connector of the SRP-X500P has the following specifications.

Terminal configuration	: D-sub 9-pin, male, inch-sized screws
Electrical specifications	: Conforms to the RS-232C standard
Connections	:

Pin No.

Name

1NC

2RXD

3TXD

4OPEN

5GND

6NC

7NC

8NC

9OPEN

1 2 3 4 5

6 7 8 9

SRP-X500P					Computer COM port
REMOTE RS-232C connector					(for D-sub 9-pin, male connector)
Name	Pin No.				Pin No.	Name
RXD	2				3	TXD

TXD	3				2	RXD

GND	5			5		GND

Page 3/43

Image 3

Contents SRP-X500P Table of Contents Connecting the SRP-X500P to a Computer About This Manual3 4 RS-232C indicator Communication FormatCommunication Protocol Communication Packet Format Handshake Codes1 AV/RGB Input Select 0x43 0x53 0x45 0x4C ‘CSEL’ Basic Control CommandsReturn packet format Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’Fader 1st-6th byte Input Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’ Output Fader Request 0x52 0x50 0x4D 0x40 ‘RPM@’Fader 1st-8th byte Remote 1-6 Level 0x43 0x4C 0x56 0x4C ‘CLVL’ Channel 1st byteRemote Level 2nd byte Master Volume UP 0x43 0x4C 0x56 0x2B ‘CLV+’ Master Volume Level 1st byteRemote 1-6 Level 2nd-7th byte Master Volume Stop 0x43 0x4C 0x56 0x53 ‘CLVS’ Master Volume Down 0x43 0x4C 0x56 0x2D ‘CLV-’Muting 2nd byte Muting 0x43 0x4D 0x55 0x54 ‘CMUT’Muting Parameter Request 0x52 0x4D 0x55 0x54 ‘RMUT’ Input Muting 1st byteSpeaker Output Muting 2nd byte Master Line Output Muting 3rd byteMaster Muting 4th byte Remote Muting 5th byteProjector Control Request 1st byte Projector ON/STANDBY 0x43 0x50 0x4A 0x50 ‘CPJP’Scene Recall Request Projector ON/STANDBY Indicator 1st byteScene Recall 0x43 0x52 0x43 0x4C ‘CRCL’ Scene Recall Request 1st byteScene No st byte Scene Recall Parameter Request 0x52 0x52 0x43 0x4C ‘RRCL’Status Acquisition Commands Index Request 0x52 0x50 0x4D 0x44 ‘RPMD’Index Level Meter Parameter Request 0x52 0x4D 0x54 0x52 ‘RMTR’ Level Meter 1st-16th byte To acquire status of single item To acquire the status of all items Parameters Input Volume 3rd-8th byte Master Volume Level 9th byteRemote 1-6 Level 10th-15th byte Input Level 16th-21st byte Output Level 22nd-29th byteInput Muting 30th byte Master Muting 33rd byte Output Muting 31st and 32nd byteSpeaker Output Muting Line Output MutingMIC 1-4 Trim 39th-42nd byte RF/AF Indicator 36th byteWL Indicator 37th byte +48V Switch 38th byteREF Indicator 49th byte Line Trim 43rd byteAV/RGB Trim 44th-48th byte FR Setup Status 54th and 55th byte Setup ChannelFR 50th-53rd byte Speaker Output CH1/2 Level Setup StatusAV/RGB Input Select 56th byte Speaker Output Level 57th, 58th byteProtection 76th byte IR Output Mode Indicator 59th byteClip Indicator 77th byte Level Meter 60th-75th byteEMG Muting 83rd byte Temperature 78th and 79th byteTemperature Projector ON/STANDBY Indicator 80th byteParallel Output 95th and 96th byte Scene No th byteParallel Input 85th-94th byte LevelOUT6 OUT5 OUT4 OUT3 OUT2 Master Volume Control 98th byteOutput FAN Motor 97th byteAGC Gain Control Gain Reduction 99th-108th byteCompressor Gain Reduction Information Maintenance Information CommandsInformation SETUPDATE2005/01/23 Information Request 0x52 0x50 0x4D 0x45 ‘RPME’Maintenance Information Read Write Maintenance Information Read WriteMaintenance Information Read only Maintenance Information Read onlyVersion Request 0x52 0x56 0x45 0x52 ‘RVER’ VersionVersion Factory Preset 0x43 0x52 0x53 0x54 ‘CRST’

Related manuals

Manual 6 pages 29.24 Kb