Sony SRP-X500P manual Temperature 78th and 79th byte, Projector ON/STANDBY Indicator 80th byte

Page 34

SRP-X500P RS-232C Interface Manual

TEMPERATURE (78th and 79th byte)

The TEMPERATURE parameter consists of 2 bytes of data in the order shown in the following table.

Byte

Parameter

1st

SPEAKER OUTPUT CH1/2 TEMPERATURE

2nd

SPEAKER OUTPUT CH3/4 TEMPERATURE

TEMPERATURE

Shows the temperature of the heat sink in the power amplifier section.

The correspondence of the parameter with the temperature is shown in the following table.

Temperature

Less than30

0x30 (‘0’)

30-34

0x31 (‘1’)

35-39

0x32 (‘2’)

40-44

0x33 (‘3’)

45-49

0x34 (‘4’)

50-54

0x35 (‘5’)

55-59

0x36 (‘6’)

60-64

0x37 (‘7’)

65-69

0x38 (‘8’)

70-74

0x39 (‘9’)

75-79

0x3A (‘:’)

80-84

0x3B (‘;’)

85-89

0x3C (‘<‘)

90-94

0x3D (‘=‘)

95-99

0x3E (‘>‘)

100or more

0x3F (‘?’)

PROJECTOR ON/STANDBY INDICATOR (80th byte)

Shows the status of the PROJECTOR ON/STANDBY POWER switch on the front panel of the SRP- X500P.

The parameter and the status of the PROJECTOR ON/STANDBY POWER switch are shown in the following table.

PROJECTOR ON/STANDBY INDICATOR

STANDBY (The switch lights up red.)

0x30 (‘0’)

ON (The switch lights up red.)

0x31 (‘1’)

Cooling down before entering STANDBY (The switch flashes green.)

0x32 (‘2’)

EMG MUTING (83rd byte)

Shows the muting status of the REMOTE PARALLEL connector using the EMG function. The parameter and the muting status using the EMG function are shown in the following table.

EMG MUTING

Muting off

0x30(‘0’)

Muting on

0x31(‘1’)

Page 34/43

Image 34
Contents SRP-X500P Table of Contents About This Manual Connecting the SRP-X500P to a Computer3 4 Communication Format RS-232C indicatorCommunication Protocol Handshake Codes Communication Packet FormatBasic Control Commands 1 AV/RGB Input Select 0x43 0x53 0x45 0x4C ‘CSEL’Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’ Return packet formatInput Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’ Fader 1st-6th byteOutput Fader Request 0x52 0x50 0x4D 0x40 ‘RPM@’ Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’Fader 1st-8th byte Channel 1st byte Remote 1-6 Level 0x43 0x4C 0x56 0x4C ‘CLVL’Remote Level 2nd byte Master Volume Level 1st byte Master Volume UP 0x43 0x4C 0x56 0x2B ‘CLV+’Remote 1-6 Level 2nd-7th byte Master Volume Down 0x43 0x4C 0x56 0x2D ‘CLV-’ Master Volume Stop 0x43 0x4C 0x56 0x53 ‘CLVS’Muting 0x43 0x4D 0x55 0x54 ‘CMUT’ Muting 2nd byteInput Muting 1st byte Muting Parameter Request 0x52 0x4D 0x55 0x54 ‘RMUT’Speaker Output Muting 2nd byte Remote Muting 5th byte Line Output Muting 3rd byteMaster Muting 4th byte MasterProjector ON/STANDBY 0x43 0x50 0x4A 0x50 ‘CPJP’ Projector Control Request 1st byteScene Recall Request 1st byte Projector ON/STANDBY Indicator 1st byteScene Recall 0x43 0x52 0x43 0x4C ‘CRCL’ Scene Recall RequestScene Recall Parameter Request 0x52 0x52 0x43 0x4C ‘RRCL’ Scene No st byteIndex Request 0x52 0x50 0x4D 0x44 ‘RPMD’ Status Acquisition CommandsIndex Level Meter Parameter Request 0x52 0x4D 0x54 0x52 ‘RMTR’ Level Meter 1st-16th byte To acquire status of single item To acquire the status of all items Parameters Master Volume Level 9th byte Input Volume 3rd-8th byteRemote 1-6 Level 10th-15th byte Output Level 22nd-29th byte Input Level 16th-21st byteInput Muting 30th byte Line Output Muting Output Muting 31st and 32nd byteSpeaker Output Muting Master Muting 33rd byte+48V Switch 38th byte RF/AF Indicator 36th byteWL Indicator 37th byte MIC 1-4 Trim 39th-42nd byteLine Trim 43rd byte REF Indicator 49th byteAV/RGB Trim 44th-48th byte Setup Channel FR Setup Status 54th and 55th byteFR 50th-53rd byte Speaker Output Level 57th, 58th byte Setup StatusAV/RGB Input Select 56th byte Speaker Output CH1/2 LevelLevel Meter 60th-75th byte IR Output Mode Indicator 59th byteClip Indicator 77th byte Protection 76th byteProjector ON/STANDBY Indicator 80th byte Temperature 78th and 79th byteTemperature EMG Muting 83rd byteLevel Scene No th byteParallel Input 85th-94th byte Parallel Output 95th and 96th byteFAN Motor 97th byte Master Volume Control 98th byteOutput OUT6 OUT5 OUT4 OUT3 OUT2Gain Reduction 99th-108th byte AGC Gain ControlCompressor Gain Reduction Information Request 0x52 0x50 0x4D 0x45 ‘RPME’ Maintenance Information CommandsInformation SETUPDATE2005/01/23 InformationMaintenance Information Read Write Maintenance Information Read WriteMaintenance Information Read only Maintenance Information Read onlyVersion Version Request 0x52 0x56 0x45 0x52 ‘RVER’Version Factory Preset 0x43 0x52 0x53 0x54 ‘CRST’
Related manuals
Manual 6 pages 29.24 Kb