Sony SRP-X500P manual Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’, Return packet format

Page 7

SRP-X500P RS-232C Interface Manual

Return packet format

When the SRP-X500P receives a command successfully, the parameter is returned together with an ACK (0x41 (‘A’)) in the order shown below.

0x41 “parameter” 0x0D

The parameter is the same as that of the AV/RGB INPUT SELECT command.

Example

When channel B input from among the AV/RGB INPUT connectors is selected 0x41 0x32 0x0D

(‘A 2 CR’)

2.1.3 INPUT FADER : 0x43 0x50 0x4D 0x35 (‘CPM5’)

This command is used to set the input fader setting.

The parameter set by this command works in the same way as the input fader setting in the OVER VIEW screen of the SRP-X500P Manager.

Packet format

0x43 0x50 0x4D 0x35 “parameter” 0x0D

♦Parameter

The parameter consists of the 6 bytes of data in order as shown in the following table.

Byte	Parameter
1st	MIC 1/WL 1 INPUT FADER
2nd	MIC 2/WL 2 INPUT FADER
3rd	MIC 3 INPUT FADER
4th	MIC 4 INPUT FADER
5th	LINE INPUT FADER
6th	AV/RGB INPUT FADER

Page 7/43

Image 7

Contents SRP-X500P Table of Contents About This Manual Connecting the SRP-X500P to a Computer3 4 Communication Format RS-232C indicatorCommunication Protocol Communication Packet Format Handshake Codes1 AV/RGB Input Select 0x43 0x53 0x45 0x4C ‘CSEL’ Basic Control CommandsReturn packet format Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’Fader 1st-6th byte Input Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’Output Fader Request 0x52 0x50 0x4D 0x40 ‘RPM@’ Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’Fader 1st-8th byte Channel 1st byte Remote 1-6 Level 0x43 0x4C 0x56 0x4C ‘CLVL’Remote Level 2nd byte Master Volume Level 1st byte Master Volume UP 0x43 0x4C 0x56 0x2B ‘CLV+’Remote 1-6 Level 2nd-7th byte Master Volume Stop 0x43 0x4C 0x56 0x53 ‘CLVS’ Master Volume Down 0x43 0x4C 0x56 0x2D ‘CLV-’Muting 2nd byte Muting 0x43 0x4D 0x55 0x54 ‘CMUT’Input Muting 1st byte Muting Parameter Request 0x52 0x4D 0x55 0x54 ‘RMUT’Speaker Output Muting 2nd byte Master Line Output Muting 3rd byteMaster Muting 4th byte Remote Muting 5th byteProjector Control Request 1st byte Projector ON/STANDBY 0x43 0x50 0x4A 0x50 ‘CPJP’Scene Recall Request Projector ON/STANDBY Indicator 1st byteScene Recall 0x43 0x52 0x43 0x4C ‘CRCL’ Scene Recall Request 1st byteScene No st byte Scene Recall Parameter Request 0x52 0x52 0x43 0x4C ‘RRCL’Index Request 0x52 0x50 0x4D 0x44 ‘RPMD’ Status Acquisition CommandsIndex Level Meter Parameter Request 0x52 0x4D 0x54 0x52 ‘RMTR’ Level Meter 1st-16th byte To acquire status of single item To acquire the status of all items Parameters Master Volume Level 9th byte Input Volume 3rd-8th byteRemote 1-6 Level 10th-15th byte Output Level 22nd-29th byte Input Level 16th-21st byteInput Muting 30th byte Master Muting 33rd byte Output Muting 31st and 32nd byteSpeaker Output Muting Line Output MutingMIC 1-4 Trim 39th-42nd byte RF/AF Indicator 36th byteWL Indicator 37th byte +48V Switch 38th byteLine Trim 43rd byte REF Indicator 49th byteAV/RGB Trim 44th-48th byte Setup Channel FR Setup Status 54th and 55th byteFR 50th-53rd byte Speaker Output CH1/2 Level Setup StatusAV/RGB Input Select 56th byte Speaker Output Level 57th, 58th byteProtection 76th byte IR Output Mode Indicator 59th byteClip Indicator 77th byte Level Meter 60th-75th byteEMG Muting 83rd byte Temperature 78th and 79th byteTemperature Projector ON/STANDBY Indicator 80th byteParallel Output 95th and 96th byte Scene No th byteParallel Input 85th-94th byte LevelOUT6 OUT5 OUT4 OUT3 OUT2 Master Volume Control 98th byteOutput FAN Motor 97th byteAGC Gain Control Gain Reduction 99th-108th byteCompressor Gain Reduction Information Maintenance Information CommandsInformation SETUPDATE2005/01/23 Information Request 0x52 0x50 0x4D 0x45 ‘RPME’Maintenance Information Read Write Maintenance Information Read WriteMaintenance Information Read only Maintenance Information Read onlyVersion Version Request 0x52 0x56 0x45 0x52 ‘RVER’Version Factory Preset 0x43 0x52 0x53 0x54 ‘CRST’

Related manuals

Manual 6 pages 29.24 Kb