Sony SRP-X500P manual Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’, Fader 1st-8th byte

Page 9

SRP-X500P RS-232C Interface Manual

2.1.5 OUTPUT FADER : 0x43 0x50 0x4D 0x40 (‘CPM@’)

This command is used to set the level of the output faders.

The parameter specified by this command functions in the same way as the output faders in the OVER VIEWscreen of the SRP-X500P Manager.

Packet format

0x43 0x50 0x4D 0x40 parameter” 0x0D

Parameter

The parameter consists of 8 bytes of data in the order shown in the following table.

Byte

Parameter

1st

SPEAKER OUTPUT 1 FADER

2nd

SPEAKER OUTPUT 2 FADER

3rd

SPEAKER OUTPUT 3 FADER

4th

SPEAKER OUTPUT 4 FADER

5th

LINE OUTPUT 1 FADER

6th

LINE OUTPUT 2 FADER

7th

LINE OUTPUT 3 FADER

8th

LINE OUTPUT 4 FADER

FADER (1st-8th byte)

The level for each output fader can be specified (in dB units).

The correspondence of the parameter with the level meter setting is the same as that of the FADER parameter of the INPUT FADER command (page 7).

Example

To specify the level for each output fader as follows:

SPEAKER OUTPUT 1 FADER

: -10dB

SPEAKER OUTPUT 2 FADER

: -10dB

SPEAKER OUTPUT 3 FADER

: -10dB

SPEAKER OUTPUT 4 FADER

: -10dB

LINE OUTPUT 1 FADER

: 0dB

LINE OUTPUT 2 FADER

: 0dB

LINE OUTPUT 3 FADER

: 0dB

LINE OUTPUT 4 FADER

: 0dB

0x43 0x50 0x4D 0x40 0x4A 0x4A 0x4A 0x4A 0x59 0x59 0x59 0x59 0x0D (‘C P M J J J J Y Y Y Y CR’)

2.1.6 OUTPUT FADER REQUEST : 0x52 0x50 0x4D 0x40 (‘RPM@’)

This command is used to read the output fader settings of the SRP-X500P.

Packet format

0x52 0x50 0x4D 0x40 0x0D

Page 9/43

Image 9
Contents SRP-X500P Table of Contents Connecting the SRP-X500P to a Computer About This Manual3 4 RS-232C indicator Communication FormatCommunication Protocol Communication Packet Format Handshake Codes1 AV/RGB Input Select 0x43 0x53 0x45 0x4C ‘CSEL’ Basic Control CommandsReturn packet format Input Fader 0x43 0x50 0x4D 0x35 ‘CPM5’Fader 1st-6th byte Input Fader Request 0x52 0x50 0x4D 0x35 ‘RPM5’Output Fader 0x43 0x50 0x4D 0x40 ‘CPM@’ Output Fader Request 0x52 0x50 0x4D 0x40 ‘RPM@’Fader 1st-8th byte Remote 1-6 Level 0x43 0x4C 0x56 0x4C ‘CLVL’ Channel 1st byteRemote Level 2nd byte Master Volume UP 0x43 0x4C 0x56 0x2B ‘CLV+’ Master Volume Level 1st byteRemote 1-6 Level 2nd-7th byte Master Volume Stop 0x43 0x4C 0x56 0x53 ‘CLVS’ Master Volume Down 0x43 0x4C 0x56 0x2D ‘CLV-’Muting 2nd byte Muting 0x43 0x4D 0x55 0x54 ‘CMUT’Muting Parameter Request 0x52 0x4D 0x55 0x54 ‘RMUT’ Input Muting 1st byteSpeaker Output Muting 2nd byte Master Muting 4th byte Line Output Muting 3rd byteRemote Muting 5th byte MasterProjector Control Request 1st byte Projector ON/STANDBY 0x43 0x50 0x4A 0x50 ‘CPJP’Scene Recall 0x43 0x52 0x43 0x4C ‘CRCL’ Projector ON/STANDBY Indicator 1st byteScene Recall Request 1st byte Scene Recall RequestScene No st byte Scene Recall Parameter Request 0x52 0x52 0x43 0x4C ‘RRCL’Status Acquisition Commands Index Request 0x52 0x50 0x4D 0x44 ‘RPMD’Index Level Meter Parameter Request 0x52 0x4D 0x54 0x52 ‘RMTR’ Level Meter 1st-16th byte To acquire status of single item To acquire the status of all items Parameters Input Volume 3rd-8th byte Master Volume Level 9th byteRemote 1-6 Level 10th-15th byte Input Level 16th-21st byte Output Level 22nd-29th byteInput Muting 30th byte Speaker Output Muting Output Muting 31st and 32nd byteLine Output Muting Master Muting 33rd byteWL Indicator 37th byte RF/AF Indicator 36th byte+48V Switch 38th byte MIC 1-4 Trim 39th-42nd byteREF Indicator 49th byte Line Trim 43rd byteAV/RGB Trim 44th-48th byte FR Setup Status 54th and 55th byte Setup ChannelFR 50th-53rd byte AV/RGB Input Select 56th byte Setup StatusSpeaker Output Level 57th, 58th byte Speaker Output CH1/2 LevelClip Indicator 77th byte IR Output Mode Indicator 59th byteLevel Meter 60th-75th byte Protection 76th byteTemperature Temperature 78th and 79th byteProjector ON/STANDBY Indicator 80th byte EMG Muting 83rd byteParallel Input 85th-94th byte Scene No th byteLevel Parallel Output 95th and 96th byteOutput Master Volume Control 98th byteFAN Motor 97th byte OUT6 OUT5 OUT4 OUT3 OUT2AGC Gain Control Gain Reduction 99th-108th byteCompressor Gain Reduction Information SETUPDATE2005/01/23 Maintenance Information CommandsInformation Request 0x52 0x50 0x4D 0x45 ‘RPME’ InformationMaintenance Information Read Write Maintenance Information Read WriteMaintenance Information Read only Maintenance Information Read onlyVersion Request 0x52 0x56 0x45 0x52 ‘RVER’ VersionVersion Factory Preset 0x43 0x52 0x53 0x54 ‘CRST’
Related manuals
Manual 6 pages 29.24 Kb