Line 6 POD X3 Family manual Serial no

Page 2

The serial number can be found on the bottom or back of your POD X3, POD X3 Live or POD X3 Pro. It’s the number that begins with “(21)”. Please note it here for future reference:

SERIAL NO:

WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION: To reduce the risk of fire or electric shock, do not remove screws. No user-serviceable parts inside. Refer servicing to qualified service personnel.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant

to Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The lightning symbol within a triangle means “electrical caution!” It indicates the presence of information about operating voltage and potential risks of electrical shock.

The exclamation point within a triangle means “caution!” Please read the information next to all caution signs.

You should read these Important Safety Instructions

Keep these instructions in a safe place

Before using your POD X3, POD X3 Live or POD X3 Pro, carefully read the applicable items of these operating instructions and safety suggestions.

1.Obey all warnings on the POD X3, POD X3 Live or POD X3 Pro, and in this Pilot’s Handbook.

2.Do not place near heat sources, such as radiators, heat registers, or appliances which produce heat.

3.Guard against objects or liquids entering the enclosure.

4.Connect only to AC power outlets rated 100-120V or 230V 47-63Hz (depending on the voltage range of the included power supply).

5.Do not step on power cords. Do not place items on top of power cords so that they are pinched or leaned on. Pay particular attention to the cord at the plug end and the point where it connects to the POD X3, POD X3 Live or POD X3 Pro.

6.Unplug your POD X3, POD X3 Live or POD X3 Pro when not in use for extended periods of time.

7.Do not perform service operations beyond those described in this Pilot’s Handbook. In the following circumstances, repairs should be performed only by qualified service personnel:

•liquid is spilled into the unit

•an object falls into the unit

•the unit does not operate normally or changes in performance in a significant way

•the unit is dropped or the enclosure is damaged

8.Prolonged listening at high volume levels may cause irreparable hearing loss and/or damage. Always be sure to practice “safe listening.”

Page 1 Page 3
Image 2
Page 1 Page 3
Contents POD X3 Family Serial no Please Note Table of Contents Appendix a Signal Flow Reference Configuration & SetupExample Setups USB & Computer SoftwarePage Tutorial POD X3 Live for Guitar Tweak the Amp Tone Controls Pick a Stomp Model and tweak it Show the Delay settings Tweak the EQ Turn both Tones on at once Select and Tweak Tone 1/Tone Tweak combined volume of Tone 1 + Tone Save Tutorial POD X3 & POD X3 Pro For GuitarTurn on the Amp Model DOUBLE-PRESS to Adjust Tap delay tempo Press down To select Lower row Tap is set to Preset loads into Tone These knobs and buttons control only one Tone at a time Controls & Connections PODControls & Connections Controls & Connections Tempo that you’ve tapped Input 2/Microphone In and Trim plug in your microphone here Controls & Connections Join the Club POD X3 Live Controls & Connections 310 Controls & Connections Controls & Connections 313 314 315 POD X3 Pro 316Controls & Connections 318 319 320 321 322 323 Page Getting Around, Tones & Tuner HomeBlock not selectedBlock selected Turn to tweak lower row settings Dual Tone Concept Hold Tone Volume Controls Preset Folders Recalling Presets You can also choose to recall only ToneRecalling User Presets on POD X3 Live Or only Tone410 Locking ToneSaving Tones 411 Tuner440HZ Page Reference Tweaking Tones Amp + CabTone Controls Guitar Amp Model Tone ControlsBass Amp Model Tone Controls Stomp Boxes Distortion Stomp BoxesDynamics Stomp Boxes ReferenceTweaking Tones Modulation Effects ReferenceTweaking Tones Delay 510 Reverb Gate Compressor 513514 Wah 515Volume Pedal 516Effects Loop POD X3 Live & POD X3 Pro only MIXPage Reference Configuration & Setup InputsOutputs Reference Configuration & Setup Outputs Page 2 Studio/Direct Mix System Page 1 Pedal and other settings SystemSystem Page 2 Pedal and other settings Commands Page Example Setups Mono or Stereo Recording or Direct to Mixer/PARecording Tone 1 & 2 to Separate Mono Tracks Feed One Guitar Amp Feed Two Guitar Amps, One for Tone 1 and One for ToneFeed Two Guitar Amps, One Wet and One Dry Example Setups Example Setups Example Setups Page USB & Computer Software Updating POD X3, POD X3 Live or POD X3 Pro’s FirmwareSetting Up For USB Recording USB Sends When Operating In Stereo Tone Mode Page Flow PpendixIgnal POD X3 Live POD X3 Pro
Top Page Image Contents