Line 6 POD X3 Family manual System Page 1 Pedal and other settings

Page 79

Reference: Configuration & Setup

to increase the digital output level of sounds that don’t have a lot of Amp Model or stompbox distortion or other settings that are driving their levels up.

Format – selects the digital output’s format, either S/PDIF or AES/EBU for POD X3 Pro, S/PDIF for POD X3 and POD X3 Live.

System

Press and hold the Outputs / Hold for System button for 2 seconds to get to the System page:

	SYSTEM
CNTRL	TONE:1	TONE:2	SETS
CNTRL	TONE:1	TONE:2	SETS
BOTH	1-W/V	1-W/V	ALL
TONES	(2-VOL)	(2-VOL)	OUTS
PEDAL	PEDALMODE	DIGPEDALLVL	MSTVOL
TONE:1	TONE:2	TONE1:	TONE2:
DELAY	DELAY	COMP	COMP
MIX	MIX
TWK	TWK	LP SW	LP SW

6•5

Press the 4-way Nav Up and Down to move between this and page 2.

System Page 1: Pedal and other settings

The Pedal-related settings here are for the wah/voume/tweak pedal built-in to POD X3 Live, and the pedal on some FBV foot controllers that can be used with POD X3 and POD X3 Pro.

Pedal – use this to have the pedal affect either Tone 1, Tone 2 or Both.

PedalTone:1 & PedalTone:2 – The built-in pedal on a POD X3 Live and some FBV foot controllers is pedal “1” and the optional external pedal you can connect to it is pedal “2”. Here you can select what those pedals control, with these choices:

•1-W/off 2-Vol – Pedal 1 controls Wah with the toe switch controlling Wah on/off. Pedal 2, if present, controls Volume.

•1-Twk 2-Vol – Pedal 1 controls whatever is assigned to Tweak in the lower half of the LCD display. Pedal 2, if present, controls Volume.

Image 79

Contents POD X3 Family Serial no Please Note Table of Contents USB & Computer Software Reference Configuration & SetupExample Setups Appendix a Signal FlowPage Tutorial POD X3 Live for Guitar Tweak the Amp Tone Controls Pick a Stomp Model and tweak it Show the Delay settings Tweak the EQ Turn both Tones on at once Select and Tweak Tone 1/Tone Tweak combined volume of Tone 1 + Tone Save For Guitar Tutorial POD X3 & POD X3 ProTurn on the Amp Model DOUBLE-PRESS to Adjust Tap delay tempo Press down To select Lower row Tap is set to Preset loads into Tone These knobs and buttons control only one Tone at a time POD Controls & ConnectionsControls & Connections Controls & Connections Tempo that you’ve tapped Input 2/Microphone In and Trim plug in your microphone here Controls & Connections Join the Club POD X3 Live Controls & Connections 310 Controls & Connections Controls & Connections 313 314 315 316 POD X3 ProControls & Connections 318 319 320 321 322 323 Page Home Getting Around, Tones & TunerBlock not selectedBlock selected Turn to tweak lower row settings Dual Tone Concept Hold Tone Volume Controls Preset Folders You can also choose to recall only Tone Recalling PresetsOr only Tone Recalling User Presets on POD X3 LiveSaving Tones Locking Tone410 440HZ Tuner411 Page Amp + Cab Reference Tweaking TonesGuitar Amp Model Tone Controls Tone ControlsBass Amp Model Tone Controls Distortion Stomp Boxes Stomp BoxesDynamics Stomp Boxes ReferenceTweaking Tones Modulation Effects ReferenceTweaking Tones Delay 510 Reverb Gate 513 Compressor514 515 Wah516 Volume PedalMIX Effects Loop POD X3 Live & POD X3 Pro onlyPage Inputs Reference Configuration & SetupOutputs Reference Configuration & Setup Outputs Page 2 Studio/Direct Mix System System Page 1 Pedal and other settingsSystem Page 2 Pedal and other settings Commands Page Mono or Stereo Recording or Direct to Mixer/PA Example SetupsRecording Tone 1 & 2 to Separate Mono Tracks Feed Two Guitar Amps, One for Tone 1 and One for Tone Feed One Guitar AmpFeed Two Guitar Amps, One Wet and One Dry Example Setups Example Setups Example Setups Page Updating POD X3, POD X3 Live or POD X3 Pro’s Firmware USB & Computer SoftwareSetting Up For USB Recording USB Sends When Operating In Stereo Tone Mode Page Ignal PpendixFlow POD X3 Live POD X3 Pro